- 您現在的位置：買賣IC網 > PDF目錄366891 > CR16HCT9VJE7 Microcontroller PDF資料下載
參數資料
| 型號： | CR16HCT9VJE7 |
| 英文描述： | Microcontroller |
| 中文描述： | 微控制器 |
| 文件頁數： | 82/157頁 |
| 文件大?。?/td> | 1256K |
| 代理商： | CR16HCT9VJE7 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁當前第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
www.national.com
82
19.3
The ACCESS.bus Interface uses the following registers:
— ACB Serial Data Register (ACBSDA)
— ACB Status Register (ACBST)
— ACB Status Control Register (ACBCST)
— ACB Control 1 Register (ACBCTL1)
— ACB Control 2 Register (ACBCTL2)
— ACB Own Address Register (ACBADDR)
ACB REGISTERS
19.3.1
The ACB Serial Data Register (ACBSDA) is a byte-wide,
read/write shift register used to transmit and receive data.
The most significant bit is transmitted (received) first and the
least significant bit is transmitted (received) last. Reading or
writing to the ACBSDA register is allowed when ACB-
ST.SDAST is set; or for repeated starts after setting the
START bit. An attempt to access the register in other cases
produces unpredictable results.
7
DATA
ACB Serial Data Register (ACBSDA)
19.3.2
The ACB Status Register (ACBST) is a byte-wide, read-only
register that maintains current ACB status. Upon reset, and
when the module is disabled, ACBST is cleared (00
16
).
7
6
5
4
SLVST
P
ACB Status Register (ACBST)
XMIT
Direction Bit. The XMIT bit is set when the ACB
module is currently in master/slave transmit
mode. Otherwise it is cleared.
MASTER. When set, the MASTER bit indicates
that the module is currently in master mode. It
is set when a request for bus mastership suc-
ceeds. It is cleared upon arbitration loss (BER
is set) or the recognition of a Stop Condition.
New match. The NMATCH bit is set when the
address byte following a Start Condition, or re-
peated starts, causes a match or a global-call
match. NMATCH is cleared when 1 is written to
it. Writing 0 to NMATCH is ignored. If
ACBCTL1.INTEN is set, an interrupt is sent
when this bit is set.
Stall After Start. The STASTR bit is set by the
successful completion of an address sending
(i.e., a Start Condition sent without a bus error,
or negative acknowledge) if ACBCTL1.STAS-
TRE is set. This bit is ignored in slave mode.
When STASTR is set, it stalls the ACCESS.bus
by pulling down the SCL line, and suspends
any other action on the bus (e.g., receives first
byte in master receive mode). In addition, if
ACBCTL1.INTEN is set, it also sends an inter-
rupt to the core. Writing 1 to STASTR clears it.
It is also cleared when the module is disabled.
Writing 0 to STASTR has no effect.
Negative acknowledge. This bit is set by hard-
ware when a transmission is not acknowledged
on the ninth clock. (In this case SDAST is not
set.) Writing 1 to NEGACK clears it. It is also
MASTER
NMATCH
STASTR
NEGACK
cleared when the module is disabled. Writing 0
to NEGACK is ignored.
Bus Error. BER is set by the hardware when a
Start or Stop Condition is detected during data
transfer (i.e., Start or Stop Condition during the
transfer of bits 2 through 8 and acknowledge
cycle), or when an arbitration problem is de-
tected. Writing 1 to BER clears it. It is also
cleared when the module is disabled. Writing 0
to BER is ignored.
SDA Status. When set, this bit indicates that
the SDA data register is waiting for data (trans-
mit - master or slave) or holds data that should
be read (receive - master or slave). This bit is
cleared when reading from the ACBSDA regis-
ter during a receive, or when written to during a
transmit. When ACBCTL1.START is set, read-
ing ACBSDA register does not clear SDAST.
This enables the ACB to send a repeated start
in master receive mode.
Slave Stop. If set, SLVSTP indicates that a
Stop Condition was detected after a slave
transfer (i.e., after a slave transfer in which
MATCH or GCMATCH is set). Writing 1 to
SLVSTP clears it. It is also cleared when the
module is disabled. Writing 0 to SLVSTP is ig-
nored.
BER
SDAST
SLVSTP
19.3.3
ACB Control Status Register (ACBCST) is a byte-wide, read/
write register that maintains current ACB status. Upon reset
and when the module is disabled, the non-reserved bits of
ACBCST are cleared (0).
7 6
5
4
Reserved TGSCL TSDA
GCMTC
ACB Control Status Register (ACBCST)
BUSY
BUSY. When BUSY is set, it indicates that the
ACB module is:
Generating a Start Condition
In Master mode (ACBST.MASTER is set)
In Slave mode (ACBCST.MATCH or
ACBCST.GCMTCH is set)
In the period between detecting a Start and
completing the reception of the address
byte. After this, the ACB either becomes
not busy or enters slave mode.
The BUSY bit is cleared by the completion of
any of the above states, and by disabling the
module. BUSY is a read only bit. It should al-
ways be written with 0.
Bus Busy When set, BB indicates the bus is
busy. It is set when the bus is active (i.e., a low
level on either SDA or SCL), or by a Start Con-
dition. It is cleared when the module is dis-
abled, upon detection of a Stop Condition, or
when writing 1 to this bit. See “Usage Hints” on
page 84 for a description of the use of this bit.
This bit should be set when either SDA or SCL
are low. This should be done by sampling the
SDA and SCL lines continuously and, setting
the bit if one of them is low. The bit remains set
BB
0
3
2
1
0
SDAST BER NEGACK STASTR
NMATC
H
MASTER
XMIT
3
2
1
BB
0
BUS
Y
H
MATC
H
相關PDF資料 |
PDF描述 |
|---|---|
| CR16HCT9VJE7Y | Microcontroller |
| CR16HCT9VJE8 | Microcontroller |
| CR16HCT9VJE8Y | Microcontroller |
| CR16HCT9VJE9 | Microcontroller |
| CR16HCT9VJE9Y | Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CR16HCT9VJE7Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE8Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE9 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| CR16HCT9VJE9Y | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。