- 您現在的位置：買賣IC網 > PDF目錄8700 > CS4382A-DQZR (Cirrus Logic Inc)IC DAC 8CH 114DB 192KHZ 48-LQFP PDF資料下載
參數資料
| 型號： | CS4382A-DQZR |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 22/50頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 8CH 114DB 192KHZ 48-LQFP |
| 標準包裝： | 2,000 |
| 位數： | 24 |
| 數據接口： | 串行 |
| 轉換器數目： | 8 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 680mW |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 16 電壓，單極 |
| 采樣率（每秒）： | 192k |
| 配用： | 598-1524-ND - BOARD EVAL FOR CS4382A DAC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
DS618F2
29
CS4382A
4.13
Recommended Procedure for Switching Operational Modes
For systems where the absolute minimum in clicks and pops is required, it is recommended that the MUTE
bits are set prior to changing significant DAC functions (such as changing sample rates or clock sources).
The mute bits may then be released after clocks have settled and the proper modes have been set.
It is required to have the device held in reset if the minimum high/low time specs of MCLK cannot be met
during clock source changes.
4.14
Control Port Interface
The Control Port is used to load all the internal register settings in order to operate in Software Mode (see
the “Filter Plots” on page 42). The operation of the Control Port may be completely asynchronous with the
audio sample rate. However, to avoid potential interference problems, the Control Port pins should remain
static if no operation is required.
The Control Port operates in one of two modes: IC or SPI.
4.14.1
MAP Auto Increment
The device has MAP (memory address pointer) auto-increment capability enabled by the INCR bit (also
the MSB) of the MAP. If INCR is set to 0, MAP will stay constant for successive IC writes or reads and
SPI writes. If INCR is set to 1, MAP will auto increment after each byte is written, allowing block reads or
writes of successive registers.
4.14.2
IC Mode
In the IC Mode, data is clocked into and out of the bi-directional serial control data line, SDA, by the serial
Control Port clock, SCL (see Figure 18 for the clock to data relationship). There is no CS pin. Pin AD0
enables the user to alter the chip address (001100[AD0][R/W]) and should be tied to VLC or GND, as re-
quired, before powering up the device. If the device ever detects a high-to-low transition on the AD0/CS
pin after power-up, SPI Mode will be selected.
4.14.2.1 IC Write
To write to the device, follow the procedure below while adhering to the Control Port Switching Specifica-
tions in Section 2.
1. Initiate a START condition to the IC bus followed by the address byte. The upper 6 bits must be
001100. The seventh bit must match the setting of the AD0 pin, and the eighth must be 0. The eighth
bit of the address byte is the R/W bit.
2. Wait for an acknowledge (ACK) from the part; then write to the memory address pointer, MAP. This
byte points to the register to be written.
3. Wait for an acknowledge (ACK) from the part; then write the desired data to the register pointed to by
the MAP.
4. If the INCR bit (see Section 4.14.1) is set to 1, repeat the previous step until all the desired registers
are written, then initiate a STOP condition to the bus.
5. If the INCR bit is set to 0 and further IC writes to other registers are desired, it is necessary to initiate
a repeated START condition and follow the procedure detailed from step 1. If no further writes to other
registers are desired, initiate a STOP condition to the bus.
相關PDF資料 |
PDF描述 |
|---|---|
| V150A36H400BF3 | CONVERTER MOD DC/DC 36V 400W |
| VI-23F-IV-S | CONVERTER MOD DC/DC 72V 150W |
| LTC2617CDE-1#PBF | IC DAC 14BIT R-R I2C 12-DFN |
| VI-23B-IV-S | CONVERTER MOD DC/DC 95V 150W |
| VI-2NN-MW-F1 | CONVERTER MOD DC/DC 18.5V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS4382A-EQZ | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:114 dB, 192 kHz 8-channel D/A Converter |
| CS4382A-EQZR | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:114 dB, 192 kHz 8-channel D/A Converter |
| CS4382-KQZ | 功能描述:數模轉換器- DAC IC 114dB 24-bit 102kHz 8Ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| CS4382-KQZR | 功能描述:數模轉換器- DAC IC 114dB 24-bit 102kHz 8Ch DAC RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| CS4383 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:114 dB, 192 kHz 8-Channel D/A Converter |
發布緊急采購，3分鐘左右您將得到回復。