- 您現在的位置：買賣IC網 > PDF目錄10684 > CS5530-ISZ (Cirrus Logic Inc)IC ADC 24BIT 1CH W/LNA 20SSOP PDF資料下載
參數資料
| 型號： | CS5530-ISZ |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 15/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 1CH W/LNA 20SSOP |
| 標準包裝： | 66 |
| 位數： | 24 |
| 采樣率（每秒）： | 3.84k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 45mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 755 (CN2011-ZH PDF) |
| 配用： | 598-1158-ND - BOARD EVAL FOR CS5530 |
| 其它名稱： | 598-1283-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
CS5530
22
DS742F3
2.4.4 Performing Calibrations
To perform a calibration, the user must send a com-
mand byte with its MSB=1, and the appropriate
calibration bits (CC2-CC0) set to choose the type
of calibration to be performed. The calibration will
be performed using the filter rate, and siganl span
(unipolar or bipolar) as set in the configuration reg-
ister. The length of time it takes to do a calibration
is slightly less than the amount of time it takes to do
a single conversion (see Table 1 for single conver-
sion timing). Offset calibration takes 608 clock cy-
cles less than a single conversion when FRS = 0,
and 729 clock cycles less when FRS = 1. Gain cal-
ibration takes 128 clock cycles less than a single
conversion when FRS = 0, and 153 clock cycles
less when FRS = 1.
Once a calibration cycle is complete, SDO falls and
the results are automatically stored in either the
gain or offset register. SDO will remain low until
the next command word is begun. If additional cal-
ibrations are performed while referencing the same
calibration registers, the last calibration results will
replace the effects from the previous calibration.
Only one calibration is performed with each com-
mand byte.
2.4.5 System Calibration
For the system calibration functions, the user must
supply the converter input calibration signals which
represent ground and full-scale. When a system off-
set calibration is performed, a ground referenced sig-
nal must be applied to the converter. Figure 10
illustrates system offset calibration.
As shown in Figure 11, the user must input a signal
representing the positive full-scale point to perform
a system gain calibration. In either case, the cali-
bration signals must be within the specified calibra-
tion limits for each specific calibration step (refer
to the System Calibration Specifications).
2.4.6 Calibration Tips
Calibration steps are performed at the output word
rate selected by the WR3-WR0 bits of the configu-
ration register. To minimize the effects of peak-to-
peak noise on the accuracy of calibration the con-
verter should be calibrated using the slowest word
rate that is acceptable.
It is recommended that
word rates of 240 Sps and higher not be used for
calibration.) To minimize digital noise near the de-
vice, the user should wait for each calibration step
to be completed before reading or writing to the se-
rial port. Reading the calibration registers and aver-
aging multiple calibrations together can produce a
more accurate calibration result. Note that access-
ing the ADC’s serial port before a calibration has
finished may result in the loss of synchronization
between the microcontroller and the ADC, and may
prematurely halt the calibration cycle.
Figure 10. System Calibration of Offset
Figure 11. System Calibration of Gain
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1443IS#TRPBF | IC COMP W/REF LOWPWR QUAD 16SOIC |
| XRD8785AID-F | IC ADC 8BIT PAR 15MSPS 24SOIC |
| LT1016CS8 | IC COMPARATOR 10NS HI-SPD 8-SOIC |
| ADCMP600BKSZ-R2 | IC COMP TTL/CMOS 1CHAN SC70-5 |
| LTC1443IDHD#PBF | IC COMP QD LP 1.182VREF 16-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS5530-ISZR | 功能描述:模數轉換器 - ADC IC 24-Bit 1-ch Low Noise ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| CS5531 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:16 BIT AND 24 BIT ADCS WITH ULTRA LOW NOISE PGIA |
| CS5531_08 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:16-bit and 24-bit ADCs with Ultra-low-noise PGIA |
| CS5531-AS | 功能描述:模數轉換器 - ADC 2-Ch 16-Bit ADCs w/ Ultra Low Noise PGIA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| CS5531-ASR | 功能描述:模數轉換器 - ADC IC 16-Bit ADCs w/UltraLw Noise PGIA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發(fā)布緊急采購，3分鐘左右您將得到回復。