- 您現在的位置：買賣IC網 > PDF目錄10684 > CS5530-ISZ (Cirrus Logic Inc)IC ADC 24BIT 1CH W/LNA 20SSOP PDF資料下載
參數資料
| 型號： | CS5530-ISZ |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 9/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 24BIT 1CH W/LNA 20SSOP |
| 標準包裝： | 66 |
| 位數： | 24 |
| 采樣率（每秒）： | 3.84k |
| 數據接口： | 串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 45mW |
| 電壓電源： | 模擬和數字，雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，單極；1 個差分，雙極 |
| 產品目錄頁面： | 755 (CN2011-ZH PDF) |
| 配用： | 598-1158-ND - BOARD EVAL FOR CS5530 |
| 其它名稱： | 598-1283-5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
CS5530
DS742F3
17
2.2.4 Reading/Writing On-Chip Registers
The CS5530’s offset, gain, and configuration regis-
ters are readable and writable while the conversion
data register is read only.
As shown in Figure 7, to write to a particular regis-
ter the user must transmit the appropriate write
command and then follow that command by 32 bits
of data. For example, to write 0x80000000 (hexa-
decimal) to the gain register, the user would first
transmit the command byte 0x02 (hexadecimal)
followed by the data 0x80000000 (hexadecimal).
Similarly, to read a particular register the user must
transmit the appropriate read command and then
acquire the 32 bits of data. Once a register is written
to or read from, the serial port returns to the com-
mand mode.
2.3 Configuration Register
To ease the architectural design and simplify the
serial interface, the configuration register is thirty-
two bits long, however, only fifteen of the thirty
two bits are used. The following sections detail the
bits in the configuration register.
2.3.1 Power Consumption
The CS5530 accommodates three power consump-
tion modes: normal, standby, and sleep. The default
mode, “normal mode”, is entered after power is ap-
plied. In this mode, the CS5530 typically consumes
35 mW. The other two modes are referred to as the
power save modes. They power down most of the
analog portion of the chip and stop filter convolu-
tions. The power save modes are entered whenever
the power down (PDW) bit of the configuration
register is set to logic 1. The particular power save
mode entered depends on state of the PSS (Power
Save Select) bit. If PSS is logic 0, the converter en-
ters the standby mode reducing the power con-
sumption to 4 mW. The standby mode leaves the
oscillator and the on-chip bias generator for the an-
alog portion of the chip active. This allows the con-
verter to quickly return to the normal mode once
PDW is set back to a logic 0. If PSS and PDW are
both set to logic 1, the sleep mode is entered reduc-
ing the consumed power to around 500
μW. Since
this sleep mode disables the oscillator, approxi-
mately a 20 ms oscillator start-up delay period is
required before returning to the normal mode. If an
external clock is used, there will be no delay.
2.3.2 System Reset Sequence
The reset system (RS) bit permits the user to per-
form a system reset. A system reset can be initiated
at any time by writing a logic 1 to the RS bit in the
configuration register. After the RS bit has been
set, the internal logic of the chip will be initialized
to a reset state. The reset valid (RV) bit is set indi-
cating that the internal logic was properly reset.
The RV bit is cleared after the configuration regis-
ter is read. The on-chip registers are initialized to
the following default states:
After reset, the RS bit should be written back to
logic 0 to complete the reset cycle. The ADC will
return to the command mode where it waits for a
valid command. Also, the RS bit is the only bit in
the configuration register that can be set when ini-
tiating a reset (i.e. a second write command is need-
ed to set other bits in the Configuration Register
after the RS bit has been cleared).
2.3.3 Input Short
The input short bit allows the user to internally
ground the inputs of the ADC. This is a useful func-
tion because it allows the user to easily test the
grounded input performance of the ADC and elim-
inate the noise effects due to the external system
components.
2.3.4 Voltage Reference Select
The voltage reference select (VRS) bit selects the
size of the sampling capacitor used to sample the
voltage reference. The bit should be set based upon
Configuration Register:
00000000(H)
Offset Register:
00000000(H)
Gain Register
01000000(H)
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1443IS#TRPBF | IC COMP W/REF LOWPWR QUAD 16SOIC |
| XRD8785AID-F | IC ADC 8BIT PAR 15MSPS 24SOIC |
| LT1016CS8 | IC COMPARATOR 10NS HI-SPD 8-SOIC |
| ADCMP600BKSZ-R2 | IC COMP TTL/CMOS 1CHAN SC70-5 |
| LTC1443IDHD#PBF | IC COMP QD LP 1.182VREF 16-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CS5530-ISZR | 功能描述:模數轉換器 - ADC IC 24-Bit 1-ch Low Noise ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| CS5531 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:16 BIT AND 24 BIT ADCS WITH ULTRA LOW NOISE PGIA |
| CS5531_08 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:16-bit and 24-bit ADCs with Ultra-low-noise PGIA |
| CS5531-AS | 功能描述:模數轉換器 - ADC 2-Ch 16-Bit ADCs w/ Ultra Low Noise PGIA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| CS5531-ASR | 功能描述:模數轉換器 - ADC IC 16-Bit ADCs w/UltraLw Noise PGIA RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。