- 您現在的位置：買賣IC網 > PDF目錄17061 > DC956A (Linear Technology)BOARD DELTA SIGMA ADC LTC2485 PDF資料下載
參數資料
| 型號： | DC956A |
| 廠商： | Linear Technology |
| 文件頁數： | 15/40頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD DELTA SIGMA ADC LTC2485 |
| 軟件下載： | QuikEval System |
| 設計資源： | DC956A Design File DC956A Schematic |
| 標準包裝： | 1 |
| 系列： | Easy Drive™, QuikEval™ |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 6.8 |
| 數據接口： | I²C，串行 |
| 工作溫度： | 0°C ~ 70°C |
| 已用 IC / 零件： | LTC2485 |
| 已供物品： | 板 |
| 相關產品： | LTC2485CDD#TRPBF-ND - IC ADC 24BIT I2C 10-DFN LTC2485IDD#TRPBF-ND - IC ADC 24BIT I2C 10-DFN LTC2485IDD#PBF-ND - IC ADC 24BIT I2C 10-DFN LTC2485CDD#PBF-ND - IC ADC 24BIT I2C 10-DFN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
LTC2485
22
2485fc
APPLICATIONS INFORMATION
For a simple approximation, the source impedance RS
driving an analog input pin (IN+, IN–, REF+ or REF–) can be
considered to form, together with RSW and CEQ (see Fig-
ure 12), a rst order passive network with a time constant
τ = (RS + RSW) CEQ. The converter is able to sample the
input signal with better than 1ppm accuracy if the sampling
period is at least 14 times greater than the input circuit time
constant τ. The sampling process on the four input analog
pins is quasi-independent so each time constant should be
considered by itself and, under worst-case circumstances,
the errors may add.
When using the internal oscillator, the LTC2485’s front-end
switched-capacitor network is clocked at 123kHz corre-
sponding to an 8.1μs sampling period. Thus, for settling
errors of less than 1ppm, the driving source impedance
should be chosen such that τ ≤ 8.1μs/14 = 580ns. When an
external oscillator of frequency fEOSC is used, the sampling
period is 2.5/fEOSC and, for a settling error of less than
1ppm, τ ≤ 0.178/fEOSC.
Automatic Differential Input Current Cancellation
In applications where the sensor output impedance is
low (up to 10kΩ with no external bypass capacitor or up
to 500Ω with 0.001μF bypass), complete settling of the
input occurs. In this case, no errors are introduced and
direct digitization of the sensor is possible.
For many applications, the sensor output impedance
combined with external bypass capacitors produces RC
time constants much greater than the 580ns required for
1ppm accuracy. For example, a 10kΩ bridge driving a 0.1μF
bypass capacitor has a time constant an order of magnitude
greater than the required maximum. Historically, settling
issues were solved using buffers. These buffers led to
increased noise, reduced DC performance (Offset/Drift),
limited input/output swing (cannot digitize signals near
ground or VCC), added system cost and increased power.
The LTC2485 uses a proprietary switching algorithm that
forces the average differential input current to zero inde-
pendent of external settling errors. This allows accurate
direct digitization of high impedance sensors without the
need of buffers (see Figures 13 to 15). Additional errors
resulting from mismatched leakage currents must also
be taken into account.
The switching algorithm forces the average input current
on the positive input (IIN+) to be equal to the average input
current on the negative input (IIN–). Over the complete
conversion cycle, the average differential input current
(IIN+ – IIN–) is zero. While the differential input current
is zero, the common mode input current (IIN++ IIN–)/2 is
proportional to the difference between the common mode
input voltage (VINCM) and the common mode reference
voltage (VREFCM).
In applications where the input common mode voltage
is equal to the reference common mode voltage, as in
the case of a balance bridge type application, both the
differential and common mode input current are zero.
The accuracy of the converter is unaffected by settling
errors. Mismatches in source impedances between IN+
and IN– also do not affect the accuracy.
In applications where the input common mode voltage is
constant but different from the reference common mode
voltage, the differential input current remains zero while
the common mode input current is proportional to the
difference between VINCM and VREFCM. For a reference
common mode of 2.5V and an input common mode of
1.5V, the common mode input current is approximately
0.74μA (in simultaneous 50Hz/60Hz rejection mode). This
common mode input current has no effect on the accuracy
if the external source impedances tied to IN+ and IN– are
matched. Mismatches in these source impedances lead
to a xed offset error but do not affect the linearity or full-
scale reading. A 1% mismatch in 1kΩ source resistances
leads to a 15ppm shift (74μV) in offset voltage.
In applications where the common mode input voltage
varies as a function of input signal level (single-ended
input, RTDs, half bridges, current sensors, etc.), the com-
mon mode input current varies proportionally with input
voltage. For the case of balanced input impedances, the
common mode input current effects are rejected by the
large CMRR of the LTC2485 leading to little degradation in
accuracy. Mismatches in source impedances lead to gain
errors proportional to the difference between the common
mode input voltage and the common mode reference
voltage. 1% mismatches in 1kΩ source resistances lead
to worst-case gain errors on the order of 15ppm or 1LSB
(for 1V differences in reference and input common mode
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B21-EY | CONVERTER MOD DC/DC 12V 50W |
| DC571A | BOARD DELTA SIGMA ADC LTC2418 |
| MIC2015-1.2YM6 TR | IC DISTRIBUTION SW 1.2A SOT23-6 |
| DC570A | BOARD DELTA SIGMA ADC LTC2440 |
| DC1012A-A | BOARD DELTA SIGMA ADC LTC2499 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DC959A | 制造商:Linear Technology 功能描述:BOARD DEMO LTC4257-1 制造商:Linear Technology 功能描述:EVAL BOARD, LTC4257CDD-1 POE |
| DC95F103V | 功能描述:熱敏電阻 - NTC 10KOhms +-.1C Epoxy Coated RoHS:否 制造商:EPCOS 電阻:10 kOhms 功率額定值:150 mW 容差:2 % 端接類型:Radial 系列:B57703M 工作溫度范圍:- 55 C to + 125 C |
| DC95F103VN | 制造商:GE Sensing & Inspection Technologies 功能描述:Thermistor;10;PCB Mount Mtg. Type;1.5In Lead;Bare Tinned Copper 制造商:GE Measurement & Control 功能描述:+/-.1oC (0oC - 70oC) Interchangeable Chip |
| DC95F103W | 功能描述:熱敏電阻 - NTC 10KOhms +-.2C Epoxy Coated RoHS:否 制造商:EPCOS 電阻:10 kOhms 功率額定值:150 mW 容差:2 % 端接類型:Radial 系列:B57703M 工作溫度范圍:- 55 C to + 125 C |
| DC95F103WN | 制造商:GE Sensing & Inspection Technologies 功能描述:Thermistor 10 PCB Mount Mtg Type 1.5Lead Bare Tinned Copper 0 +70 制造商:GE Sensing & Inspection Technologies / Thermometrics 功能描述:THERMISTOR NTC +60 10KOHM 制造商:GE Measurement & Control 功能描述:+/-.2oC (0oC - 70oC) Interchangeable Chip 制造商:GE MEASUREMENT & CONTROL/GE SENSING 功能描述:THERMISTOR, NTC, +60C, 10KOHM; Thermistor Type:NTC; Resistance:10kohm; Thermistor Case Style:Radial Leaded; No. of Pins:2; Operating Temperature Min:-40C; Operating Temperature Max:60C; Operating Temperature Range:-40C to +60C ;RoHS Compliant: Yes |
發(fā)布緊急采購，3分鐘左右您將得到回復。