- 您現在的位置：買賣IC網 > PDF目錄376802 > DM9008F (Electronic Theatre Controls, Inc.) ISA/Plug & Play Super Ethernet Contoller PDF資料下載
參數資料
| 型號： | DM9008F |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | ISA/Plug & Play Super Ethernet Contoller |
| 中文描述： | 的ISA /插頭 |
| 文件頁數： | 15/68頁 |
| 文件大?。?/td> | 403K |
| 代理商： | DM9008F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
DM9008
ISA/Plug & Play Super Ethernet Contoller
Final
Version :DM9008-DS-F02
June 14, 2000
15
Command Register (CR)
The Command Register is used to initiate transmissions,
enable or disable Remote DMA operations, and select register
pages. To issue a command, the microprocessor sets the
corresponding bit(s) (RD2, RD1, RD0, TXP). Further
commands may be overlapped, but with the following rules: (1)
If a transmit command overlaps a remote DMA operation, bits
RD0, RD1, and RD2 must be maintained for the remote DMA
command when the TXP bit is set. Note that if a remote DMA
command is re-issued when the transmit command is given,
the DMA will be completed immediately if the remote byte
count register has not been reinitialized. (2) If a remote DMA
operation overlaps a transmission, RD0, RD1, and RD2 may
be written with the desired values and a "0" may be written to
the TXP bit. Writing a "0" to this bit has no effect. (3) remote
write DMA may not overlap a remote read operation or vice
versa. Either of these operations must either be completed or
be aborted before the other operation may start. Bits PS1,
PS0, RD2 and STP may be set at any time.
7
6
5
4
3
2
1
0
PS1
PS0
RD2
RD1
RD0
TXP
STA
STP
Bit
Symbol
Description
D0
STP
STOP: Software reset command. Takes the controller off-line, and no packets will be received
or transmitted. Any reception or transmission in progress will continue to completion before the
reset state is entered. To exit this state, the STP bit must be reset. The software reset is
executed only when indicated by the RST bit in the ISR being set to a "1." STP powers up
high
D1
STA
Start mode
D2
TXP
Transmit Packet: This bit must be set to initiate transmission of a packet. TXP is internally reset
after the transmission is either completed or aborted. This bit should be set only after the
Transmit Byte Count and Transmit Page Start registers have been programmed. TXP powers
up low
D3
D4
D5
RD0
RD1
RD2
Remote DMA Command: These three encoded bits control operation of the Remote DMA
channel. RD2 can be set to abort any Remote DMA command in progress. The Remote
Byte Count Registers should be cleared when a Remote DMA has been aborted. The
Remote Start Addresses are not restored to the starting address if the Remote DMA is
aborted. RD2 powers up high
RD2 RD1 RD0
0 0 0 Not Allowed
0 0 1 Remote Read
0 1 0 Remote Write
0 1 1 Send Packet
1 X X Abort/Complete Remote DMA
D6
D7
PS0
PS1
Page Select: These two encoded bits select which register page is to be accessed with
addresses SA0-3
PS1 PS0
0 0 Register Page 0
0 1 Register Page 1
1 0 Register Page 2
1 1 Register Page 3
相關PDF資料 |
PDF描述 |
|---|---|
| DM9081 | 10BASE-T Hub Controller |
| DM9081F | 10BASE-T Hub Controller |
| DM9095 | Twisted-Pair Medium Attachment Unit |
| DM9095L | Twisted-Pair Medium Attachment Unit |
| DM9102D | SINGLE CHIP FAST ETHEMET NIC CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DM9009CJ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual 4-input NAND Gate |
| DM9009CN | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Dual 4-input NAND Gate |
| DM9010 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Single Chip Ethernet Controller with General Processor Interface |
| DM9010_06 | 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:10/100 Mbps Single Chip Ethernet Controller with General Processor Interface |
| DM9010B | 制造商:DAVICOM 制造商全稱:DAVICOM 功能描述:10/100 Mbps Single Chip Ethernet Controller With General Processor Interface |
發布緊急采購，3分鐘左右您將得到回復。