- 您現在的位置：買賣IC網 > PDF目錄9371 > DS1338Z-3+T&R (Maxim Integrated Products)IC RTC 56BYTE NV RAM 3V 8-SOIC PDF資料下載
參數資料
| 型號： | DS1338Z-3+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RTC 56BYTE NV RAM 3V 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 時鐘/日歷 |
| 特點： | 閏年，NVSRAM，方波輸出 |
| 存儲容量： | 56B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.3 V ~ 3.7 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
DS1338 I2C RTC with 56-Byte NV RAM
13 of 16
Depending upon the state of the R/W bit, two types of data transfer are possible:
1)
Data transfer from a master transmitter to a slave receiver. The master transmits the first byte (the slave
address). Next follows a number of data bytes. The slave returns an acknowledge bit after each received byte.
Data is transferred with the most significant bit (MSB) first.
2)
Data transfer from a slave transmitter to a master receiver. The master transmits the first byte (the slave
address). The slave then returns an acknowledge bit, which is followed by the slave transmitting a number of
data bytes. The master returns an acknowledge bit after all received bytes other than the last byte. At the end
of the last received byte, a “not acknowledge” is returned. The master device generates all of the serial clock
pulses and the START and STOP conditions. A transfer is ended with a STOP condition or with a repeated
START condition. Since a repeated START condition is also the beginning of the next serial transfer, the bus is
not released. Data is transferred with the most significant bit (MSB) first.
The DS1338 can operate in the following two modes:
1)
Slave receiver mode (write mode): Serial data and clock are received through SDA and SCL. An
acknowledge bit is transmitted after each byte is received. START and STOP conditions are recognized as the
beginning and end of a serial transfer. Hardware performs address recognition after reception of the slave
address and direction bit (Figure 6). The slave address byte is the first byte received after the master
generates the START condition. The slave address byte contains the 7-bit DS1338 address—1101000—
followed by the direction bit (R/W), which, for a write, is 0. After receiving and decoding the slave address byte,
the slave outputs an acknowledge on the SDA line. After the DS1338 acknowledges the slave address and
write bit, the master transmits a register address to the DS1338. This sets the register pointer on the DS1338,
with DS1338 acknowledging the transfer. The master may then transmit zero or more bytes of data, with the
DS1338 acknowledging each byte received. The register pointer increments after each data byte is transferred.
The master generates a STOP condition to terminate the data write.
2)
Slave transmitter mode (read mode): The first byte is received and handled as in the slave receiver mode.
However, in this mode, the direction bit indicates that the transfer direction is reversed. The DS1338 transmits
serial data on SDA while the serial clock is input on SCL. START and STOP conditions are recognized as the
beginning and end of a serial transfer (Figure 7). The slave address byte is the first byte received after the
master generates the START condition. The slave address byte contains the 7-bit DS1338 address—
1101000—followed by the direction bit (R/W), which, for a read, is 1. After receiving and decoding the slave
address byte, the slave outputs an acknowledge on the SDA line. The DS1338 then starts transmitting data
using the register address pointed to by the register pointer. If the register pointer is not set before the initiation
of a read mode, the first address that is read is the last one stored in the register pointer. The register pointer is
incremented after each byte is transferred. The DS1338 must receive a “not acknowledge” to end a read.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-262-MW | CONVERTER MOD DC/DC 15V 100W |
| DS1307Z+T&R/C01 | IC RTC SERIAL 8-SOIC |
| VI-J62-MZ | CONVERTER MOD DC/DC 15V 25W |
| VE-261-MX-B1 | CONVERTER MOD DC/DC 12V 75W |
| M83723/72A2041N | CONN RCPT 41POS WALL MT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1339 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C Serial Real-Time Clock |
| DS1339_06 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C Serial Real-Time Clock |
| DS1339_11 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:I2C Serial Real-Time Clock Trickle-Charge Capability |
| DS1339A | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Current, I2C, Serial Real-Time Clock |
| DS1339A_13 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Low-Current, I2C, Serial Real-Time Clock |
發布緊急采購，3分鐘左右您將得到回復。