參數資料
型號： DS21FT44
廠商： MAXIM INTEGRATED PRODUCTS INC
元件分類： Digital Transmission Controller
英文描述： DATACOM, FRAMER, PBGA300
封裝： 27 X 27 MM, 1.27 MM PITCH, MCMBGA-300
文件頁數： 45/117頁
文件大?。?/td> 691K
代理商： DS21FT44
DS21FT44/DS21FF44
33 of 117
IDR: DEVICE IDENTIFICATION REGISTER (Address = 0F Hex)
(MSB)
(LSB)
T1E1
0
ID3
ID2
ID1
ID0
SYMBOL
POSITION
NAME AND DESCRIPTION
T1E1
IDR.7
T1 or E1 Chip Determination Bit
0 = T1 chip
1 = E1 chip
ID3
IDR.3
Chip Revision Bit 3. MSB of a decimal code that represents
the chip revision.
ID2
IDR.1
Chip Revision Bit 2
ID1
IDR.2
Chip Revision Bit 1
ID0
IDR.0
Chip Revision Bit 0. LSB of a decimal code that represents
the chip revision.
RCR1: RECEIVE CONTROL REGISTER 1 (Address = 10 Hex)
(MSB)
(LSB)
RSMF
RSM
RSIO
—
FRC
SYNCE
RESYNC
SYMBOL
POSITION
NAME AND DESCRIPTION
RSMF
RCR1.7
RSYNC Multiframe Function. Only used if the RSYNC pin
is programmed in the multiframe mode (RCR1.6 = 1).
0 = RSYNC outputs CAS multiframe boundaries
1 = RSYNC outputs CRC4 multiframe boundaries
RSM
RCR1.6
RSYNC Mode Select
0 = frame mode (See timing diagrams in Section 22.)
1 = multiframe mode (See timing diagrams in Section 22.)
RSIO
RCR1.5
RSYNC I/O Select. (Note: this bit must be set to zero when
RCR2.1 = 0).
0 = RSYNC is an output (depends on RCR1.6)
1 = RSYNC is an input (only valid if elastic store enabled)
—
RCR1.4
Not Assigned. Should be set to zero when written.
—
RCR1.3
Not Assigned. Should be set to zero when written.
FRC
RCR1.2
Frame Resync Criteria
0 = resync if FAS received in error three consecutive times
1 = resync if FAS or bit 2 of non-FAS is received in error
three consecutive times
SYNCE
RCR1.1
Sync Enable
0 = auto resync enabled
1 = auto resync disabled
RESYNC
RCR1.0
Resync. When toggled from low to high, a resync is initiated.
Must be cleared and set again for a subsequent resync.
相關PDF資料
PDF描述
DS21Q352 DATACOM, PCM TRANSCEIVER, PBGA256
DS21Q354 DATACOM, PCM TRANSCEIVER, PBGA256
DS21Q41BT DATACOM, FRAMER, PQFP128
DS21Q42TN DATACOM, FRAMER, PQFP128
DS21Q42T DATACOM, FRAMER, PQFP128
相關代理商/技術參數
參數描述
DS21FT44+ 功能描述:網絡控制器與處理器 IC 4X3 E1 Framer E1 Framer E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21FT44N 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21FT44N+ 功能描述:網絡控制器與處理器 IC 4x4 16/4x3 12 Chnl E1/E1 Framer RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q348 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q348B 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*