參數資料
型號： DS21Q48N
廠商： Maxim Integrated Products
文件頁數： 28/73頁
文件大小： 0K
描述： IC LIU E1/T1/J1 4X 5V LONG144BGA
標準包裝： 90
類型： 線路接口裝置（LIU）
規程： E1
電源電壓： 4.75 V ~ 5.25 V
安裝類型： 表面貼裝
封裝/外殼： 144-BBGA
供應商設備封裝： 144-PBGA（17x17）
包裝： 管件
DS2148/DS21Q48
34 of 73
SYMBOL
POSITION
DESCRIPTION
RJAB
CCR6.3
RCLK Jitter Attenuator Bypass. This control bit allows the recovered
received clock and data to bypass the jitter attenuation while still
allowing the BPCLK output to use the jitter attenuator. See Figure 1-1
and Section 7.1 for details.
0 = disabled
1 = enabled
ECRS2
CCR6.2
Error Count Register Select 2. See Section 6.4 for details.
ECRS1
CCR6.1
Error Count Register Select 1. See Section 6.4 for details.
ECRS0
CCR6.0
Error Count Register Select 0. See Section 6.4 for details.
5 STATUS REGISTERS
There are three registers that contain information on the current real-time status of the device, status
register (SR), and receive information registers 1 and 2 (RIR1/RIR2). When a particular event has
occurred (or is occurring), the appropriate bit in one of these three registers will be set to a one. Some of
the bits in SR, RIR1, and RIR2 are latched bits and some are real-time bits. The register descriptions
below list which status bits are latched and which are real-time bits. For latched status bits, when an event
or an alarm occurs the bit is set to a one and will remain set until the user reads that bit. The bit will be
cleared when it is read and it will not be set again until the event has occurred again. Two of the latched
status bits (RUA1 & RCL) will remain set after reading if the alarm is still present.
The user will always precede a read of any of the three status registers with a write. The byte written to
the register will inform the DS2148 which bits the user wishes to read and have cleared. The user will
write a byte to one of these registers with a one in the bit positions to be read and a zero in the other bit
positions. When a one is written to a bit location, that location will be updated with the latest information.
When a zero is written to a bit position, that bit position will not be updated and the previous value will
be held. A write to the status and information registers will be immediately followed by a read of the
same register. The read result should be logically ANDed with the mask byte that was just written and
this value should be written back into the same register to ensure that bit does indeed clear. This second
write step is necessary because the alarms and events in the status registers occur asynchronously with
respect to their access via the parallel port. This write-read-write scheme allows an external
microcontroller or microprocessor to individually poll certain bits without disturbing the other bits in the
register. This operation is key in controlling the DS2148 with higher-order software languages.
The bits in the SR register have the unique ability to initiate a hardware interrupt via the
INT output pin.
Each of the alarms and events in the SR can be either masked or unmasked from the interrupt pin via the
interrupt mask register (IMR). The interrupts caused by the RCL, RUA1, and LOTC bits in SR act
differently than the interrupts caused by the other status bits in SR. The RCL, RUA1 and LOTC bits will
force the
INT pin low whenever they change state (i.e., go active or inactive). The INT pin will be
allowed to return high (if no other interrupts are present) when the user reads the alarm bit that caused the
interrupt to occur even if the alarm is still present. The other status bits in SR can force the
INT pin low
when they are set. The
INT pin will be allowed to return high (if no other interrupts are present) when the
user reads the event bit that caused the interrupt to occur.
相關PDF資料
PDF描述
VI-262-MX-F4 CONVERTER MOD DC/DC 15V 75W
VE-B6Y-MY-S CONVERTER MOD DC/DC 3.3V 33W
DS21Q348N IC LIU T1/E1/J1 QUAD 3.3V 144BGA
MS3451L18-1SW CONN RCPT 10POS CBL MNT W/SCKT
D38999/26MH53SB CONN PLUG 53POS STRAIGHT W/SCKT
相關代理商/技術參數
參數描述
DS21Q48NB 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q50 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Quad E1 Transceiver
DS21Q50L 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q50L+ 功能描述:網絡控制器與處理器 IC Quad E1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS21Q50L-C01 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*