參數資料
型號： DS3150TN
廠商： Maxim Integrated Products
文件頁數： 2/28頁
文件大小： 0K
描述： IC LIU T3/E3/STS-1 IND 48-TQFP
產品培訓模塊： Lead (SnPb) Finish for COTS
產品變化通告： Product Discontinuation 20/Feb/2012
標準包裝： 250
類型： 線路接口裝置（LIU）
驅動器/接收器數： 1/1
規程： DS3
電源電壓： 3.135 V ~ 3.465 V
安裝類型： 表面貼裝
封裝/外殼： 48-LQFP
供應商設備封裝： 48-LQFP（7x7）
包裝： 管件
DS3150
10 of 28
1.2 Transmitter
Transmit Clock. The clock applied at the TCLK input is used to clock in data on the TPOS/TNRZ and
TNEG pins. If the jitter attenuator is not enabled in the transmit path, the signal on TCLK is the transmit
line clock and must be transmission quality (i.e.,
±20ppm frequency accuracy and low jitter). If the jitter
attenuator is enabled in the transmit path, the signal on TCLK can be jittery and/or periodically gapped
(not exceeding 8 UI) but must still have an average frequency within
±20ppm of the nominal line rate.
When enabled in the transmit path, the jitter attenuator generates the transmit line clock from the signal
applied on the MCLK pin. The signal on MCLK must, therefore, be a transmission-quality clock
(
±20ppm frequency accuracy and low jitter). The duty cycle of TCLK is not restricted as long as the high
and low times listed in Section 3 are met.
To support a glueless interface to a variety of neighboring components, the polarity of TCLK can be
inverted using the ICE input pin. See the ICE pin description in Table 2-A for details.
Framer Interface Format and the B3ZS/HDB3 Encoder. Data to be transmitted can be input in
either NRZ or bipolar format. To select the bipolar format, wire the
ZCSE input pin high. In this format,
the B3ZS/HDB3 encoder is disabled, and the data to be transmitted is sampled on the TPOS and TNEG
input pins. Positive-polarity pulses are indicated by TPOS = 1 while negative-polarity pulses are indicated
by TNEG = 1. TPOS and TNEG should not be active at the same time.
To select the NRZ format, wire
ZCSE low. In this format, the B3ZS/HDB3 encoder is enabled, and the
data to be transmitted is sampled on the TNRZ pin. The TNEG pin is ignored in NRZ mode and should
be tied low.
Pattern Generation. The transmitter can generate a number of different patterns internally, including
unframed all ones (E3 AIS), 1010…, and DS3 AIS. See Figure 1-5 for the structure of the DS3 AIS
signal. The TDS0 and TDS1 inputs are used to select these on-board patterns. Table 2-B indicates the
possible selections.
Waveshaping, Line Build-Out, Line Driver. The waveshaping block converts the transmit clock,
positive data, and negative data signals into a single AMI signal that meets applicable
telecommunications standards when transmitted on 75
W coaxial cable. Table 1-C through Table 1-G and
Figure 1-4 show the waveform template specifications and test parameters from ANSI T1.102, Telcordia
GR-253-CORE and GR-499-CORE, and ITU-T G.703.
Because DS3 and STS-1 signals must meet the waveform templates at the cross-connect through any
cable length from 0 to 450 feet, the waveshaping circuitry includes a selectable LBO feature. For cable
lengths of 225 feet or greater, the LBO pin should be low. When LBO is low, output pulses are driven
onto the coaxial cable without any preattenuation. For cable lengths less than 225 feet, LBO should be
high. When LBO is high, pulses are preattenuated before being driven onto the coaxial cable. The LBO
circuitry provides attenuation that mimics the attenuation of 225 feet of coaxial cable.
To power down the transmitter and tri-state the TX+ and TX- output pins, pull the
TTS input pin low.
Interfacing to the Line. The transmitter interfaces to the outgoing DS3/E3/STS-1 coaxial cable (75
W)
through a 2:1 step-down transformer connected to the TX+ and TX- output pins. Figure 1-2 shows the
arrangement of the transformer and other recommended interface components.
相關PDF資料
PDF描述
DS3154N+ IC LIU DS3/E3/STS-1 QD 144CSBGA
DS3164+ IC ATM/PACKET PHY QUAD 400-BGA
DS3170+ IC TXRX DS3/E3 100-CSBGA
DS3172N+ IC TXRX DS3/E3 DUAL 400-BGA
DS3181N+ IC ATM/PACKET PHY W/LIU 400PBGA
相關代理商/技術參數
參數描述
DS3150TN+ 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3150TN1 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
DS3150TNC1 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3150TNC1+ 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS3151 功能描述:網絡控制器與處理器 IC Single DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*