- 您現在的位置：買賣IC網 > PDF目錄1915 > DS3150TN (Maxim Integrated Products)IC LIU T3/E3/STS-1 IND 48-TQFP PDF資料下載
參數資料
| 型號： | DS3150TN |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 27/28頁 |
| 文件大小： | 0K |
| 描述： | IC LIU T3/E3/STS-1 IND 48-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 產品變化通告： | Product Discontinuation 20/Feb/2012 |
| 標準包裝： | 250 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | DS3 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
DS3150
8 of 28
For E3
LOS Assertion:
1) The ALOS circuitry detects that the incoming signal is less than or equal to a signal level
approximately 24dB below nominal and mutes the data coming out of the clock and data recovery
block. (24dB below nominal is in the “tolerance range” of G.775, where LOS may or may not be
declared.)
2) The DLOS detector counts 175
±75 consecutive zeros coming out of the clock and data recovery
block and asserts
LOS. (175
±75 meets the 10 N 255 pulse interval duration requirement of
G.775.)
For E3
LOS Clear:
1) The ALOS circuitry detects that the incoming signal is greater than or equal to a signal level
approximately 18dB below nominal and enables data to come out of the clock and data recovery
block. (18dB below nominal is in the “tolerance range” of G.775 where LOS may or may not be
declared.)
2) The DLOS detector counts 175
±75 consecutive pulse intervals without excessive zero occurrences
and deasserts
LOS. (175
±75 meets the 10 N 255 pulse interval duration requirement of G.775.)
The requirements of ANSI T1.231 for STS-1 LOS defects are supported by the DLOS detector. At STS-1
rate, the time required for the DLOS detector to count 175
±75 consecutive zeros falls in the range of
2.3
T100ms required by ANSI T1.231 for declaring an LOS defect. Although the time required for the
DLOS detector to count 175
±75 consecutive pulse intervals with no excessive zeros is less than the
125s to 250
ms period required by ANSI T1.231 for clearing an LOS defect, a period of this length where
LOS is inactive can easily be timed in software.
During LOS, the RCLK output signal is derived from the device’s master clock. The ALOS detector has a
longer time constant than the DLOS detector. Thus, when the incoming signal is lost, the DLOS detector
activates first, asserting the
LOS pin, followed by the ALOS detector. When a signal is restored, the
DLOS detector does not get a valid signal that it can qualify for no excessive zero occurrences until the
ALOS detector has seen the incoming signal rise above a signal level approximately 18dB below
nominal.
Framer Interface Format and the B3ZS/HDB3 Decoder. The recovered data can be output in
either NRZ or bipolar format. To select the bipolar format, wire the
ZCSE input pin high. In this format,
the B3ZS/HDB3 decoder is disabled, and the recovered data is buffered and output on the RPOS and
RNEG output pins. Received positive-polarity pulses are indicated by RPOS = 1, while negative-polarity
pulses are indicated by RNEG = 1. In bipolar interface format the receiver simply passes on the data
received and does not check it for bipolar violations or excessive zero occurrences.
To select the NRZ format, wire
ZCSE low. In this format, the B3ZS/HDB3 decoder is enabled, and the
recovered data is decoded and output as a composite NRZ value on the RNRZ pin. Code violations are
flagged on the RLCV pin. In the discussion that follows, a valid pulse that conforms to the AMI rule is
denoted as B. A pulse that violates the AMI rule is known as bipolar violation (BPV) and is denoted as V.
In DS3 and STS-1 modes, B3ZS decoding is performed. RLCV is asserted during any RCLK cycle where
the data on RNRZ causes ones of the following code violations:
§ A BPV immediately preceded by a valid pulse (B, V)
§ A BPV with the same polarity as the last BPV
相關PDF資料 |
PDF描述 |
|---|---|
| DS3154N+ | IC LIU DS3/E3/STS-1 QD 144CSBGA |
| DS3164+ | IC ATM/PACKET PHY QUAD 400-BGA |
| DS3170+ | IC TXRX DS3/E3 100-CSBGA |
| DS3172N+ | IC TXRX DS3/E3 DUAL 400-BGA |
| DS3181N+ | IC ATM/PACKET PHY W/LIU 400PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3150TN+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TN1 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS3150TNC1 | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TNC1+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3151 | 功能描述:網絡控制器與處理器 IC Single DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。