- 您現在的位置：買賣IC網 > PDF目錄377001 > DSP56F807VF80E (飛思卡爾半導體(中國)有限公司) 16-bit Digital Signal Controllers PDF資料下載
參數資料
| 型號： | DSP56F807VF80E |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 16-bit Digital Signal Controllers |
| 中文描述： | 16位數字信號控制器 |
| 文件頁數： | 56/60頁 |
| 文件大?。?/td> | 522K |
| 代理商： | DSP56F807VF80E |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁當前第56頁第57頁第58頁第59頁第60頁
56F807 Technical Data Technical Data, Rev. 15
56
Freescale Semiconductor
Measure the thermal resistance from the junction to where the leads are attached to the case. This definition
is approximately equal to a junction to board thermal resistance.
Use the value obtained by the equation (T
J
– T
T
)/P
D
where T
T
is the temperature of the package case
determined by a thermocouple.
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimizing the size of the clearance is important to minimize the change in
thermal performance caused by removing part of the thermal interface to the heat sink. Because of the
experimental difficulties with this technique, many engineers measure the heat sink temperature and then
back-calculate the case temperature using a separate measurement of the thermal resistance of the
interface. From this case temperature, the junction temperature is determined from the junction-to-case
thermal resistance.
5.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation:
Provide a low-impedance path from the board power supply to each V
DD
pin on the controller, and from the
board ground to each V
SS
pin.
The minimum bypass requirement is to place 0.1
μ
F capacitors positioned as close as possible to the
package supply pins. The recommended bypass configuration is to place one bypass capacitor on each of
the V
DD
/V
SS
pairs, including V
DDA
/V
SSA.
Ceramic and tantalum capacitors tend to provide better
performance tolerances.
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or electrical
fields. However, normal precautions are advised to
avoid application of any voltages higher than maximum
rated voltages to this high-impedance circuit. Reliability
of operation is enhanced if unused inputs are tied to an
appropriate voltage level.
相關PDF資料 |
PDF描述 |
|---|---|
| DSP56F807 | 16-bit Hybrid Controller(16位混合控制器) |
| DSP56F826BU80 | 16-bit Digital Signal Controllers |
| DSP56F826BU80E | 16-bit Digital Signal Controllers |
| DSP56F826E | 16-bit Digital Signal Controllers |
| DSP56F826 | 16-bit Hybrid Controller(16位混合控制器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSP56F807VF80E | 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC |
| DSP56F807VF80J | 制造商:Freescale Semiconductor 功能描述:DSP 16BIT - Trays |
| DSP56F826 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:16-bit Digital Signal Controllers |
| DSP56F826-827UM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor Users Manual |
| DSP56F826-827UM/D | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:56F827 16-bit Hybrid Controller |
發布緊急采購，3分鐘左右您將得到回復。