參數資料
型號： ENC624J600-I/PT
廠商： Microchip Technology
文件頁數： 51/168頁
文件大?。?/td> 0K
描述： IC ETHERNET CTRLR W/SPI 64-TQFP
視頻文件： Fast 100 Mbps Ethernet PICtail Plus Overview
標準包裝： 160
控制器類型： 以太網控制器（IEEE 802.3）
接口： SPI
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 96mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 64-TQFP
供應商設備封裝： 64-TQFP（10x10）
包裝： 托盤
產品目錄頁面： 684 (CN2011-ZH PDF)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
PIC18F2220/2320/4220/4320
DS39599G-page 142
2007 Microchip Technology Inc.
In addition to the expanded functions of the CCP1CON
register, the ECCP module has two additional registers
associated with enhanced PWM operation and
Auto-Shutdown features:
PWM1CON
ECCPAS
All other registers associated with the ECCP module are
identical to those used for the CCP1 module in
PIC18F2X20 devices, including register and individual bit
names. Likewise, the timer assignments and interactions
between the two CCP modules are identical, regardless
of whether CCP1 is a standard or enhanced module.
16.1
ECCP Outputs
The Enhanced CCP module may have up to four outputs
depending on the selected operating mode. These out-
puts, designated P1A through P1D, are multiplexed with
I/O pins on PORTC and PORTD. The pin assignments
are summarized in Table 16-1.
To configure I/O pins as PWM outputs, the proper PWM
mode must be selected by setting the P1Mx and
CCP1Mx bits (CCP1CON<7:6> and <3:0>, respec-
tively). The appropriate TRISC and TRISD direction
bits for the port pins must also be set as outputs.
16.2
Capture and Compare Modes
The Capture and Compare modes of the ECCP module
are identical in operation to that of CCP1, as discussed
“Compare Mode”. No changes are required when
moving between these modules on PIC18F2X20 and
PIC18F4X20 devices.
16.3
Standard PWM Mode
When configured in Single Output mode, the ECCP
module functions identically to the standard CCP
module in PWM mode, as described in Section 15.4
TABLE 16-1:
PIN ASSIGNMENTS FOR VARIOUS ECCP MODES
bit 3-0
CCP1M3:CCP1M0: ECCP Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCP module)
0001 = Unused (reserved)
0010 = Compare mode, toggle output on match (CCP1IF bit is set)
0011 = Unused (reserved)
0100 = Capture mode, every falling edge
0101 = Capture mode, every rising edge
0110 = Capture mode, every 4th rising edge
0111 = Capture mode, every 16th rising edge
1000 = Compare mode, set output on match (CCP1IF bit is set)
1001 = Compare mode, clear output on match (CCP1IF bit is set)
1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin operates
as a port pin for input and output)
1011 = Compare mode, trigger special event (CCP1IF bit is set, ECCP resets TMR1or TMR2 and
starts an A/D conversion if the A/D module is enabled)
1100 = PWM mode, P1A, P1C active-high, P1B, P1D active-high
1101 = PWM mode, P1A, P1C active-high, P1B, P1D active-low
1110 = PWM mode, P1A, P1C active-low, P1B, P1D active-high
1111 = PWM mode, P1A, P1C active-low, P1B, P1D active-low
REGISTER 16-1:
CCP1CON: ECCP CONTROL REGISTER (40/44-PIN DEVICES) (CONTINUED)
Note:
When setting up single output PWM opera-
tions, users are free to use either of the pro-
cesses described in Section 15.5.3 “Setup
more generic but will work for either single
or multi output PWM.
ECCP Mode
CCP1CON Configuration
RC2
RD5
RD6
RD7
Compatible CCP
00xx11xx
CCP1
RD5/PSP5
RD6/PSP6
RD7/PSP7
Dual PWM
10xx11xx
P1A
P1B
RD6/PSP6
Quad PWM
x1xx11xx
P1A
P1B
P1C
P1D
Legend: x = Don’t care. Shaded cells indicate pin assignments not used by ECCP in a given mode.
Note 1: TRIS register values must be configured appropriately.
2: With ECCP in Dual or Quad PWM mode, the PSP input/output control of PORTD is overridden by P1B,
P1C and P1D.
相關PDF資料
PDF描述
ISL88694IH5 IC ACCELERATOR SMBUS SOT-5
GJM1555C1HR30BB01D CAP CER 0.3PF 50V NP0 0402
GJM1555C1HR20BB01D CAP CER 0.2PF 50V NP0 0402
ISL33001IUZ-T IC BUS BUFF HOTSWAP 2WR 8MSOP
PIC12C508AT-04/SN IC MCU OTP 512X12 8SOIC
相關代理商/技術參數
參數描述
ENC624J600T-I/PT 功能描述:外圍驅動器與原件 - PCI 10/100 Base-T Stand alone Ethernet Ctrlr RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
ENC624J600T-IML 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC624J600T-IPT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC680D05B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC680D-05B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*