參數資料
型號： EVAL-AD1940MINIBZ
廠商： Analog Devices Inc
文件頁數： 13/36頁
文件大?。?/td> 0K
描述： BOARD EVAL AD1940 MINI SIGMADSP
標準包裝： 1
系列： SigmaDSP®
主要目的： 音頻，音頻處理
嵌入式： 是，DSP
已用 IC / 零件： AD1940
主要屬性： 單芯片多通道 28/56 位音頻 DSP
次要屬性： 均衡，交叉，低音增強，多頻帶動態處理，延遲等
已供物品： 板，線纜，CD，電源，USB 適配器
產品目錄頁面： 775 (CN2011-ZH PDF)
相關產品： AD1940YSTZ-ND - IC DSP AUDIO 16CH/28BIT 48-LQFP
AD1940YSTZRL-ND - IC DSP AUDIO 16CH/28BIT 48-LQFP
AD1940/AD1941
Rev. B | Page 20 of
36
RECOMMENDED PROGRAM/PARAMETER
LOADING PROCEDURES
When writing large amounts of data to the program or para-
meter RAM in direct write mode, the processor core should be
disabled to prevent unpleasant noises from appearing at the
audio output. The AD1940/AD1941 contain several
mechanisms for disabling the core.
If the loaded program does not use the target/slew RAM as the
main system volume control (for example, the default power-up
program),
1.
Assert Bit 9 (low to assert—default setting) and Bit 6 (high
to assert) of the core control register. This zeroes the
accumulators, the serial output registers, and the serial
input registers.
2.
Fill the program RAM using burst mode writes.
3.
Fill the parameter RAM using burst mode writes.
4.
Assert Bit 7 of the core control register to initiate a data-
memory clear sequence. Wait at least 100 μs for this
sequence to complete. This bit is automatically cleared after
the operation is complete.
5.
Deassert Bit 9 and Bit 6 of the core control register to allow
the core to begin normal operation
If the loaded program does use the target/slew RAM as the
main system volume control,
1.
Assert Bit 12 of the core control register. This begins a
volume ramp down, with a time constant determined by
the upper bits of the target RAM. Wait for this ramp down
to complete (the user may poll Bit 13 of the core control
register, or simply wait for a given amount of time).
2.
Assert Bit 9 (low to assert) and Bit 6 (high to assert) of the
core control register. This zeroes the accumulators, the
serial output registers, and the serial input registers.
3.
Fill the program RAM using burst mode writes.
4.
Fill the parameter RAM using burst mode writes.
5.
Assert Bit 7 of the core control register to initiate a data-
memory clear sequence. Wait at least 100 μs for this
sequence to complete. This bit is automatically cleared after
the operation is complete.
6.
Deassert Bit 9 and Bit 6 of the core control register.
7.
If the newly loaded program also uses the target/slew
RAM, deassert Bit 12 of the core control register to begin a
volume ramp up procedure.
TARGET/SLEW RAM
The target/slew RAM is a bank of 64 RAM locations, each of
which can be set to autoramp from one value to a desired final
value in one of four modes.
Summary
The target/slew RAM is used by the DSP when a program is
loaded into the program RAM that uses one or more locations
in the slew RAM to access internal coefficient data. Typically,
these coefficients are used for volume controls or smooth cross-
fading effects, but may be used to update any value in the para-
meter RAM. Each of the 64 locations in the slew RAM are
linked to corresponding locations in the target RAM. When a
new value is written to the target RAM using the control
port, the corresponding slew RAM location begins to ramp
toward the target. The value is updated once per audio frame
(LRCLK period).
The target RAM is 34 bits wide. The lower 28 bits contain the
target data in 5.23 format for the linear and exponential
(constant dB and RC type) ramp types. For constant time
ramping, the lower 28 bits contain 16 bits in 2.14 format and
12 bits to set the current step. The upper six bits are used to
determine the type and speed of the ramp envelope in all
modes. The format of the data write for linear and exponential
formats is shown in Table 19. Table 20 shows the data write
format for the constant time ramping.
Data can only be written to the target/slew RAM using the
safeload registers as described in the Safeload Registers section.
A mute slew RAM bit is included in the core control register to
simultaneously set all the slew RAM target values to 0. This is
useful for implementing a global multichannel mute. When this
bit is deasserted, all slew RAM values return to their original
premuted states.
Table 19. Linear, Constant dB, and RC Type
Ramp Data Write
Byte 0
Byte 1
Bytes 2–4
000000, curve_type [1:0]
time_const [3:0],
data [27:24]
Data [23:0]
Table 20. Constant Time Ramp Data Write
Byte 0
Byte 1
Bytes 2–4
000000,
curve_type [1:0]
update_step [0],
#_of_steps [2:0], data
[15:12]
Data [11:0],
reserved [11:0]
相關PDF資料
PDF描述
ADN8830ACPZ IC CTRLR THERMO COOLER 32-LFCSP
MAX674CSA+T IC VREF SERIES PREC 10V 8-SOIC
RSC06DRXN-S734 CONN EDGECARD 12POS DIP .100 SLD
SDR1006-100ML INDUCTOR POWER 10UH 2.6A SMD
AD9520-4/PCBZ BOARD EVAL FOR AD9520-4
相關代理商/技術參數
參數描述
EVAL-AD1941EB 制造商:Analog Devices 功能描述:EVAL BD SIGMADSPMULTICHANAUDIO PROCESSOR - Bulk
EVAL-AD1953EB 制造商:Analog Devices 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk 制造商:Analog Devices 功能描述:EVALUATION KIT ((NS))
EVAL-AD1953EBZ 制造商:Analog Devices 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk
EVAL-AD1954EB 制造商:Rochester Electronics LLC 功能描述:EVAL BRD FOR 3 CH 24 BIT SIG-PROCESS DAC - Bulk 制造商:Analog Devices 功能描述:
EVAL-AD1955EB 制造商:Analog Devices 功能描述:Evaluation Board For AD1955 制造商:Analog Devices 功能描述:EVAL BOARD FOR 24 BIT 192KHZ DAC 120 DB - Bulk 制造商:Rochester Electronics LLC 功能描述:EVAL BOARD FOR 24 BIT 192KHZ DAC 120 DB - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*