- 您現在的位置：買賣IC網 > PDF目錄17082 > EVAL-AD5443-DBRDZ (Analog Devices Inc)BOARD EVAL CARD CLINUX/STAMP PDF資料下載
參數資料
| 型號： | EVAL-AD5443-DBRDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 10/25頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL CARD CLINUX/STAMP |
| 產品培訓模塊： | DAC Architectures |
| 標準包裝： | 1 |
| DAC 的數量： | 1 |
| 位數： | 12 |
| 采樣率（每秒）： | 2.5M |
| 數據接口： | 串行 |
| 設置時間： | 50ns |
| DAC 型： | 電流 |
| 工作溫度： | -40°C ~ 125°C |
| 已供物品： | 板，CD |
| 已用 IC / 零件： | AD5443 |
| 產品目錄頁面： | 788 (CN2011-ZH PDF) |
| 相關產品： | AD5443YRMZ-REEL7-ND - IC DAC 12BIT SERIAL IN 10MSOP AD5443YRMZ-REEL-ND - IC DAC 12BIT SERIAL IN 10MSOP AD5443YRMZ-ND - IC DAC 12BIT SERIAL IOUT 10-MSOP AD5443YRM-ND - IC DAC 12BIT SERIAL IOUT 10-MSOP |
Data Sheet
AD5426/AD5432/AD5443
Rev. G | Page 17 of 24
SINGLE-SUPPLY APPLICATIONS
Current Mode Operation
These DACs are specified and tested to guarantee operation
in single-supply applications. In the current mode circuit of
applied to VBIAS.
VOUT
GND
VIN
IOUT2
IOUT1
RFB
A1
VREF
VDD
VBIAS
VDD
C1
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE
REQUIRED IF A1 IS A HIGH SPEED AMPLIFIER.
A1
03162-044
A2
Figure 43. Single-Supply Current Mode Operation
In this configuration, the output voltage is given by
VOUT = {D × (RFB/RDAC) × (VBIAS VIN)} + VBIAS
(AD5443), the output voltage varies from
VOUT = VBIAS to VOUT = 2 VBIAS VIN
VBIAS should be a low impedance source capable of sinking and
sourcing all possible variations in current at the IOUT2 terminal
without any problems.
It is important to note that VIN is limited to low voltages because
the switches in the DAC ladder no longer have the same source
drain drive voltage. As a result, their on resistance differs, which
degrades the linearity of the DAC. See Figure 15 to Figure 20.
Voltage Switching Mode of Operation
Figure 44 shows these DACs operating in the voltage switching
mode. The reference voltage, VIN, is applied to the IOUT1 pin,
IOUT2 is connected to AGND, and the output voltage is available
at the VREF terminal. In this configuration, a positive reference
voltage results in a positive output voltage, making single-
supply operation possible. The output from the DAC is voltage
at a constant impedance (the DAC ladder resistance), thus an
op amp is necessary to buffer the output voltage. The reference
input no longer sees a constant input impedance, but one that
varies with code. Therefore, the voltage input should be driven
from a low impedance source.
VIN
R2
R1
VOUT
GND
IOUT1
RFB
A1
VREF
VDD
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED
IF A1 IS A HIGH SPEED AMPLIFIER.
03162-045
Figure 44. Single-Supply Voltage Switching Mode Operation
It is important to note that VIN is limited to low voltages because
the switches in the DAC ladder no longer have the same source
drain drive voltage. As a result, their on resistance differs, which
degrades the linearity of the DAC.
Also, VIN must not go negative by more than 0.3 V or an
internal diode turns on, exceeding the maximum ratings of the
device. In this type of application, the full range of multiplying
capability of the DAC is lost.
POSITIVE OUTPUT VOLTAGE
Note that the output voltage polarity is opposite to the VREF
polarity for dc reference voltages. To achieve a positive voltage
output, an applied negative reference to the input of the DAC
is preferred over the output inversion through an inverting
amplifier because of the resistor’s tolerance errors. To generate
a negative reference, the reference can be level shifted by an
op amp such that the VOUT and GND pins of the reference
become the virtual ground and 2.5 V, respectively, as shown
NOTES
1. ADDITIONAL PINS OMITTED FOR CLARITY.
2. C1 PHASE COMPENSATION (1pF TO 2pF) MAY BE REQUIRED IF A1 IS
A HIGH SPEED AMPLIFIER.
VOUT = 0V
TO +2.5V
GND
IOUT2
IOUT1
RFB
A1
VREF
VDD = 5V
VDD
C1
GND
VIN
VOUT
ADR03
–2.5V
–5V
+5V
03162-046
Figure 45. Positive Voltage Output with Minimum of Components
相關PDF資料 |
PDF描述 |
|---|---|
| ADR291GRUZ-REEL7 | IC VREF SERIES PREC 2.5V 8-TSSOP |
| REF195GRUZ | IC VREF SERIES PREC 5V 8-TSSOP |
| V24C5E125B2 | CONVERTER MOD DC/DC 5V 125W |
| AP2152AMPG-13 | IC PWR SW USB 2CH 0.5A 8-MSOP |
| SCRH127-220 | INDUCTOR SMD 22UH 3.60A 1KHZ |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD5443EB | 制造商:Analog Devices 功能描述:EVAL BD FOR AD5443, 0BIT HIGH BANDWIDTH MULTIPLYING DACS W/ - Bulk |
| EVAL-AD5443EBZ | 功能描述:BOARD EVAL FOR AD5433 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5443SDZ | 功能描述:BOARD EVAL FOR AD5443 RoHS:是 類別:編程器，開發系統 >> 評估板 - 數模轉換器 (DAC) 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- DAC 的數量:4 位數:12 采樣率（每秒）:- 數據接口:串行，SPI? 設置時間:3µs DAC 型:電流/電壓 工作溫度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| EVAL-AD5444EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD5444EBZ | 制造商:Analog Devices 功能描述:EVAL KIT FOR 12-/14BIT HIGH BANDWIDTH MULTIPLYING DACS W/ SE - Bulk |
發布緊急采購，3分鐘左右您將得到回復。