- 您現在的位置：買賣IC網 > PDF目錄17038 > EVAL-AD7693CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7693 PDF資料下載
參數資料
| 型號： | EVAL-AD7693CBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7693 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 500k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 18mW @ 500kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7693 |
| 已供物品： | 板 |
| 相關產品： | AD7693BRMZRL7-ND - IC ADC 16BIT 500KSPS 10-MSOP AD7693BCPZRL7TR-ND - IC ADC 16BIT 500KSPS 10-LFCSP AD7693BRMZ-ND - IC ADC 16BIT 500KSPS 10-MSOP AD7693BCPZRL-ND - IC ADC 16BIT 500KSPS 10LFCSP |
AD7693
Rev. A | Page 19 of 24
CS MODE, 4-WIRE WITHOUT BUSY INDICATOR
This mode is usually used when multiple AD7693s are
connected to an SPI-compatible digital host.
A connection diagram example using two AD7693s is shown in
With SDI high, a rising edge on CNV initiates a conversion,
selects the CS mode, and forces SDO to high impedance. In this
mode, CNV must be held high during the conversion phase and
the subsequent data readback. (If SDI and CNV are low, SDO is
driven low.) Prior to the minimum conversion time, SDI can be
used to select other SPI devices, such as analog multiplexers,
but SDI must be returned high before the minimum conversion
time elapses and then held high for the maximum possible
conversion time to avoid the generation of the busy signal
indicator. When the conversion is complete, the AD7693 enters
the acquisition phase and powers down. Each ADC result can
be read by bringing its SDI input low, which consequently
outputs the MSB onto SDO. The remaining data bits are clocked
by subsequent SCK falling edges. The data is valid on both SCK
edges. Although the rising edge can be used to capture the data,
a digital host using the SCK falling edge will allow a faster
reading rate, provided it has an acceptable hold time. After the
16th SCK falling edge or when SDI goes high (whichever occurs
first), SDO returns to high impedance and another AD7693 can
be read.
DATA IN
CLK
CS1
CONVERT
CS2
CNV
SCK
SDO
SDI
CNV
SCK
SDO
SDI
AD7693
0
63
94
-0
37
DIGITAL HOST
Figure 38. CS Mode, 4-Wire Without Busy Indicator Connection Diagram
SDO
D15
D14
D13
D1
D0
tDIS
SCK
12
3
30
31
32
tHSDO
tDSDO
tEN
CONVERSION
ACQUISITION
tCONV
tCYC
tACQ
ACQUISITION
SDI(CS1)
CNV
tSSDICNV
tHSDICNV
D1
14
15
tSCK
tSCKL
tSCKH
D0
D16
D15
17
18
16
SDI(CS2)
0
63
94
-03
8
Figure 39. CS Mode, 4-Wire Without Busy Indicator Serial Interface Timing
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7676CBZ | BOARD EVALUATION FOR AD7676 |
| LGU2W820MELZ | CAP ALUM 82UF 450V 20% SNAP |
| EBM22DCMN-S288 | CONN EDGECARD 44POS .156 EXTEND |
| MPC8306-SOM | MODULE BOARD FOR MPC830X |
| EVAL-AD7610CBZ | BOARD EVALUATION FOR AD7610 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7693SDZ | 功能描述:數據轉換 IC 開發工具 EVAL BOARD 16-bit ADC 500kSPS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-AD7694CB | 制造商:Analog Devices 功能描述: |
| EVAL-AD7694CB1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 250 kSPS PulSAR ADC in MSOP |
| EVAL-AD7694CBZ | 功能描述:BOARD EVALUATION FOR AD7694 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7694SDZ | 功能描述:數據轉換 IC 開發工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。