- 您現在的位置：買賣IC網 > PDF目錄17038 > EVAL-AD7693CBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7693 PDF資料下載
參數資料
| 型號： | EVAL-AD7693CBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7693 |
| 標準包裝： | 1 |
| 系列： | PulSAR® |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 500k |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF |
| 在以下條件下的電源（標準）： | 18mW @ 500kSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7693 |
| 已供物品： | 板 |
| 相關產品： | AD7693BRMZRL7-ND - IC ADC 16BIT 500KSPS 10-MSOP AD7693BCPZRL7TR-ND - IC ADC 16BIT 500KSPS 10-LFCSP AD7693BRMZ-ND - IC ADC 16BIT 500KSPS 10-MSOP AD7693BCPZRL-ND - IC ADC 16BIT 500KSPS 10LFCSP |
AD7693
Rev. A | Page 23 of 24
APPLICATION HINTS
LAYOUT
The printed circuit board that houses the AD7693 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. The pinout of the
AD7693, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these
couple noise onto the die unless a ground plane under the
AD7693 is used as a shield. Fast switching signals, such as CNV
or clocks, should not run near analog signal paths. Crossover of
digital and analog signals should be avoided.
At least one ground plane should be used. It could be common
or split between the digital and analog sections. In the latter
case, the planes should be joined underneath the AD7693s.
The AD7693 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the power supplies VDD and VIO of the AD7693
should be decoupled with ceramic capacitors, typically 100 nF,
placed close to the AD7693 and connected using short, wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of a layout following these rules is shown in
EVALUATING AD7693 PERFORMANCE
Other recommended layouts for the AD7693 are outlined
in the documentation of the evaluation board for the AD7693
(EVAL-AD7693CB). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-CONTROL BRD3.
0639
4-
045
Figure 46. Example Layout of the AD7693 (Top Layer)
0
63
94
-0
46
Figure 47. Example Layout of the AD7693 (Bottom Layer)
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7676CBZ | BOARD EVALUATION FOR AD7676 |
| LGU2W820MELZ | CAP ALUM 82UF 450V 20% SNAP |
| EBM22DCMN-S288 | CONN EDGECARD 44POS .156 EXTEND |
| MPC8306-SOM | MODULE BOARD FOR MPC830X |
| EVAL-AD7610CBZ | BOARD EVALUATION FOR AD7610 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7693SDZ | 功能描述:數據轉換 IC 開發工具 EVAL BOARD 16-bit ADC 500kSPS RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-AD7694CB | 制造商:Analog Devices 功能描述: |
| EVAL-AD7694CB1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:16-Bit, 250 kSPS PulSAR ADC in MSOP |
| EVAL-AD7694CBZ | 功能描述:BOARD EVALUATION FOR AD7694 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7694SDZ | 功能描述:數據轉換 IC 開發工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。