- 您現在的位置：買賣IC網 > PDF目錄17060 > EVAL-AD7739EBZ (Analog Devices Inc)BOARD EVAL FOR AD7739 PDF資料下載
參數資料
| 型號： | EVAL-AD7739EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 11/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7739 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 24 |
| 采樣率（每秒）： | 15.1k |
| 數據接口： | 串行 |
| 輸入范圍： | ±2.5 V |
| 在以下條件下的電源（標準）： | 85mW @ 5V |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7739 |
| 已供物品： | 板 |
| 相關產品： | AD7739BRUZ-REEL7-ND - IC ADC 24BIT 8CH SIG-DEL 24TSSOP AD7739BRUZ-ND - IC ADC 24BIT 8-CH 24-TSSOP AD7739BRU-REEL-ND - IC ADC 24BIT 8CH SIG-DEL 24TSSOP AD7739BRU-ND - IC ADC 24BIT 8-CH 24-TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Data Sheet
AD7739
Rev. A | Page 19 of 32
CHANNEL CONVERSION TIME REGISTERS
8 Bits, Read/Write Registers, Address 0x30 to
Address 0x37, Default Value 0x91
The conversion time registers enable or disable chopping and
configure the digital filter for a particular channel (see Table 25
and Table 26). This register value affects the conversion time,
frequency response, and noise performance of the ADC.
MODE REGISTER
8 Bits, Read/Write Register, Address 0x38 to
Address 0x3F, Default Value 0x00
The mode register configures the part and determines its operating
mode (see Table 27, Table 28, and Table 29). Writing to the
mode register clears the ADC status register, sets the RDY pin
to a logic high level, exits all current operations, and starts the
mode specified by the mode bits.
The AD7739 contains only one mode register. The two LSBs of
the address are used for writing to the mode register to specify
the channel selected for the operation determined by the MD2
to MD0 bits. Only the address 0x38 must be used for reading
from the mode register.
Table 25. Channel Conversion Time Registers Bits
Bit
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mnemonic
Chop
FW (7-bit filter word)
Default
1
0x11
Table 26. Channel Conversion Time Registers Bit Descriptions
Bit
Mnemonic
Description
7
Chop
Chopping enable bit. Set to 1 to apply chopping mode for a particular channel.
6 to 0
FW
Chop = 1, single conversion or continuous conversion with one channel enabled.
Conversion Time (s) = (FW × 128 + 262)/MCLK Frequency (MHz), the FW range is 2 to 127.
Chop = 1, continuous conversion with two or more channels enabled.
Conversion Time (s) = (FW × 128 + 263)/MCLK Frequency (MHz), the FW range is 2 to 127.
Chop = 0, single conversion or continuous conversion with one channel enabled.
Conversion Time (s) = (FW × 64 + 213)/MCLK Frequency (MHz), the FW range is 3 to 127.
Chop = 0, continuous conversion with two or more channels enabled.
Conversion Time (s) = (FW × 64 + 214)/MCLK Frequency (MHz), the FW range is 3 to 127.
Table 27. Mode Register Bits
Bit
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Mnemonic
MD2
MD1
MD0
CLKDIS
Dump
Cont RD
24/16 BIT
Clamp
Default
0
Table 28. Mode Register Bit Descriptions
Bit
Mnemonic
Description
7 to 5
MD2 to MD0
Mode bits. These three bits determine the AD7739 operation mode. Writing a new value to the mode bits exit
the part from the mode in which it has been operating and place it in the newly requested mode immediately.
The function of the mode bits follows.
MD2
MD1
MD0
Mode
Address Used for Mode Register Write
Specifies
0
Idle
0
1
Continuous conversion
First channel to start converting
0
1
0
Single conversion
Channel to convert
0
1
Power-down (standby)
1
0
ADC zero-scale self-calibration
Conversion time for calibration
1
0
1
ADC full-scale self-calibration (for 2.5 V)
Conversion time for calibration
1
0
Channel zero-scale system calibration
Channel to calibrate
1
Channel full-scale system calibration
Channel to calibrate
相關PDF資料 |
PDF描述 |
|---|---|
| EEV-HA1H330UP | CAP ALUM 33UF 50V 20% SMD |
| VE-B3B-EY | CONVERTER MOD DC/DC 95V 50W |
| EVAL-AD7738EBZ | BOARD EVAL FOR AD7738 |
| EVAL-AD7767-1EDZ | BOARD EVAL AD7767-1 64KSPS 111DB |
| EEV-HA1E470P | CAP ALUM 47UF 25V 20% SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7741/42EB | 制造商:Analog Devices 功能描述:Evaluation Board For Single And Multi-Channel Synchronous Voltage-To-Frequency Converters 制造商:Analog Devices 功能描述:EVALUATION BOARD IC - Bulk |
| EVAL-AD7741/42EBZ | 功能描述:BOARD EVAL FOR AD7741/7742 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7741-42EBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:Single and Multichannel, Synchronous Voltage-to-Frequency Converters |
| EVAL-AD7746EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:24-Bit Capacitance-to-Digital Converter with Temperature Sensor |
| EVAL-AD7746EBZ | 功能描述:BOARD EVALUATION FOR AD7746 RoHS:是 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
發布緊急采購，3分鐘左右您將得到回復。