- 您現在的位置：買賣IC網 > PDF目錄16568 > EVAL-AD7879EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7879 PDF資料下載
參數資料
| 型號： | EVAL-AD7879EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/41頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7879 |
| 標準包裝： | 1 |
| 主要目的： | 接口，觸摸屏控制器 |
| 嵌入式： | 否 |
| 已用 IC / 零件： | AD7879 |
| 主要屬性： | 4 線電阻式觸控屏控制器，I²C 和 SPI 接口 |
| 次要屬性： | 圖形用戶界面，USB 接口 |
| 已供物品： | 板，線纜，CD，觸控屏 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
AD7879/AD7889
Rev. C | Page 15 of 40
TOUCH-PRESSURE MEASUREMENT
The pressure applied to the touch screen by a pen or finger can
also be measured with the AD7879/AD7889 using some simple
calculations. The contact resistance between the X and Y plates
is measured, providing a good indication of the size of the
depressed area and, therefore, the applied pressure. The area of
the spot that is touched is proportional to the size of the object
touching it. The size of this resistance (RTOUCH) can be calculated
using two different methods.
First Method
The first method requires the user to know the total resistance
of the X-plate tablet (RX). Three touch screen conversions are
required: measurement of the X position, XPOSITION (Y+ input);
measurement of the X+ input with the excitation voltage applied
to Y+ and X (Z1 measurement); and measurement of the Y
input with the excitation voltage applied to Y+ and X (Z2
measurement). These three measurements are illustrated in
The AD7879/AD7889 have two special ADC channel settings
that configure the X and Y switches for the Z1 and Z2 measure-
ments and store the results in the Z1 and Z2 result registers. The
Z1 measurement is selected by setting the CHNL ADD[2:0] bits
to 101 in Control Register 1 (Address 0x01); the result is stored
in the X+ (Z1) result register (Address 0x0A). The Z2 measurement
is selected by setting the CHNL ADD[2:0] bits to 100 in Control
Register 1 (Address 0x01); the result is stored in the Y (Z2)
result register (Address 0x0B).
The touch resistance (RTOUCH) can then be calculated using the
following equation:
RTOUCH = (RXPLATE) × (XPOSITION/4096) × [(Z2/Z1) 1]
(2)
07667-
026
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z1 POSITION
X–
X+
Y–
Y+
TOUCH
RESISTANCE
MEASURE
X POSITION
Y–
Y+
X–
X+
TOUCH
RESISTANCE
MEASURE
Z2 POSITION
Figure 26. Three Measurements Required for Touch Pressure
Second Method
The second method requires the user to know the resistance of
the X-plate and Y-plate tablets. Three touch screen conversions
are required: a measurement of the X position (XPOSITION), the
Y position (YPOSITION), and the Z1 position.
The following equation also calculates the touch resistance
(RTOUCH):
RTOUCH = RXPLATE × (XPOSITION/4096) × [(4096/Z1) 1]
RYPLATE × [1 (YPOSITION/4096)]
(3)
TEMPERATURE MEASUREMENT
A temperature measurement option called the single-conversion
method is available on the AD7879/AD7889. The conversion
method requires only a single measurement on ADC Channel
001. The results are stored in the temperature conversion result
register (Address 0x0D). The AD7879/AD7889 do not provide
an explicit output of the temperature reading; the system must
perform some external calculations. This method is based on
an on-chip diode measurement.
The acquisition time is fixed at 16 ms for temperature
measurement.
Conversion Method
The conversion method makes use of the fact that the tempera-
ture coefficient of a silicon diode is approximately 2.1 mV/°C.
However, this small change is superimposed on the diode forward
voltage, which can have a wide tolerance. Therefore, it is necessary
to calibrate by measuring the diode voltage at a known temperature
to provide a baseline from which the change in forward voltage
with temperature can be measured. This method provides a
resolution of approximately 0.3°C and a predicted accuracy
of ±2°C.
The temperature limit comparison is performed on the result
in the temperature conversion result register (Address 0x0D),
which is the measurement of the diode forward voltage. The
values programmed into the high and low limits should be
referenced to the calibrated diode forward voltage to make
accurate limit comparisons.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-JWR-EZ-S | CONVERTER MOD DC/DC 7.5V 25W |
| GCC08DREI-S734 | CONN EDGECARD 16POS .100 EYELET |
| MAX8594ETG+T | IC PMIC W/DC-DC SUP 24-TQFN |
| VI-JWP-EZ-S | CONVERTER MOD DC/DC 13.8V 25W |
| VI-JWM-EZ-S | CONVERTER MOD DC/DC 10V 25W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7887CB | 制造商:Analog Devices 功能描述:EVAL BD FOR 2.7 V TO 5.25 V, MICROPWR, 2CH, 125 KSPS, 12-BIT - Bulk |
| EVAL-AD7887CB4 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead MSOP |
| EVAL-AD7887CBZ | 功能描述:BOARD EVAL FOR AD7887 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7888CB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 2.7 V TO 5.25 V, MICROPWR, 8CH, 125 KSPS, 12-BI - Bulk |
| EVAL-AD7890-2 | 制造商:Analog Devices 功能描述:AD7890 EVAL BOARD |
發布緊急采購，3分鐘左右您將得到回復。