參數資料
型號： EVAL-AD9838SDZ
廠商： Analog Devices Inc
文件頁數： 14/32頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD9838
產品培訓模塊： Direct Digital Synthesis Tutorial Series (1 of 7): Introduction
Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action
Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter
Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction
Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter
Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator
標準包裝： 1
主要目的： 計時，直接數字合成（DDS）
嵌入式： 否
已用 IC / 零件： AD9838
主要屬性： USB 供電或外部電源
次要屬性： SPI 接口
已供物品： 板，線纜，CD，文檔
AD9838
Rev. A | Page 21 of 32
IOUT AND IOUTB PINS
SIGN BIT OUT PIN
The AD9838 offers a variety of outputs from the chip. The
digital outputs are available from the SIGN BIT OUT pin. The
available outputs are the comparator output or the MSB of the
DAC data. The bits controlling the SIGN BIT OUT pin are
listed in Table 18.
The analog outputs from the AD9838 are available from the
IOUT and IOUTB pins. The available outputs are a sinusoidal
output or a triangular output (see Table 19).
Note that the SLEEP pin and the SLEEP12 bit must be set to 0
(the DAC is enabled) when using the IOUT and IOUTB pins.
Table 18. Outputs from the SIGN BIT OUT Pin
OPBITEN
Bit
MODE
Bit
SIGN/PIB
Bit
DIV2
Bit
SIGN BIT OUT Pin
0
X
High impedance
1
0
DAC data MSB/2
1
0
1
DAC data MSB
1
0
1
0
Reserved
1
0
1
Comparator output
1
X
Reserved
Table 19. Outputs from the IOUT and IOUTB Pins
OPBITEN Bit
MODE Bit
IOUT and IOUTB Pin Output
0
Sinusoid
0
1
Triangle
1
0
Sinusoid
1
Reserved
Sinusoidal Output
The SIN ROM converts the phase information from the
frequency and phase registers into amplitude information,
resulting in a sinusoidal signal at the output. To obtain a
sinusoidal output from the IOUT and IOUTB pins, set the
MODE bit (Bit D1) to 0.
The SIGN BIT OUT pin must be enabled before use. The
OPBITEN bit (Bit D5) in the control register enables and dis-
ables this pin. When OPBITEN = 1, the SIGN BIT OUT pin is
enabled. Note that if OPBITEN = 1, the MODE bit (Bit D1) in
the control register should be set to 0.
Triangle Output
Comparator Output
The SIN ROM can be bypassed so that the truncated digital output
from the NCO is sent to the DAC. In this case, the output is no
longer sinusoidal. The DAC produces a 10-bit linear triangular
function (see Figure 23). To obtain a triangle output from the
IOUT and IOUTB pins, set the MODE bit (Bit D1) to 1 and the
OPBITEN bit (Bit D5) to 0.
The AD9838 has an on-board comparator. To connect this com-
parator to the SIGN BIT OUT pin, the OPBITEN bit (Bit D5)
and the SIGN/PIB bit (Bit D4) must be set to 1. After filtering
the sinusoidal output from the DAC, the waveform can be
applied to the comparator to generate a square waveform.
MSB of the DAC Data
3π/2
7π/2
11π/2
VOUT MAX
VOUT MIN
09
07
7-
02
7
The MSB of the DAC data can be output from the AD9838.
By setting the OPBITEN bit (Bit D5) to 1 and the SIGN/PIB bit
(Bit D4) to 0, the MSB of the DAC data is available at the SIGN
BIT OUT pin. This output is useful as a coarse clock source.
The square wave can also be divided by 2 before being output.
The DIV2 bit (Bit D3) in the control register controls the
frequency of this output from the SIGN BIT OUT pin.
Figure 23. Triangle Output
POWERING UP THE AD9838
The flowchart in Figure 24 shows the operating routine for the
AD9838. When the AD9838 is powered up, the part should be
reset. This resets the appropriate internal registers to 0 to provide
an analog output of midscale. To avoid spurious DAC outputs
during AD9838 initialization, the RESET pin or the RESET bit
should be set to 1 until the part is ready to begin generating
an output.
A reset does not reset the phase, frequency, or control registers.
These registers will contain invalid data and, therefore, should
be set to known values by the user. The RESET pin or bit should
then be set to 0 to begin generating an output. The data appears
on the DAC output eight or nine MCLK cycles after the RESET
pin or bit is set to 0.
相關PDF資料
PDF描述
A3AAH-2036M IDC CABLE - ASC20H/AE20M/ASC20H
M1CXA-3436R IDC CABLE - MKC34A/MC34M/X
M1AXA-3436R IDC CABLE - MSC34A/MC34M/X
B82477R4472M100 INDUCTOR POWER 4.7UH 7.5A SMD
860529-8 CONN LEAD ASSY DBL-END 20AWG 10"
相關代理商/技術參數
參數描述
EVAL-AD9880-ABZ 功能描述:KIT MODULE VIDEO INPUT AD9880 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板
EVAL-ADAS1000EBZU1 功能描述:EVAL BOARD ADAS1000 ECG AFE RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板
EVAL-ADAS1000SDZ 功能描述:數據轉換 IC 開發工具 EVALUATION BOARD RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
EVAL-ADAS1000SDZU3 制造商:Analog Devices 功能描述:EVALUATION KIT - Boxed Product (Development Kits)
EVAL-ADAS1000SDZU4 制造商:Analog Devices 功能描述:EVAL BOARD ANAS1000 ECG AFE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*