參數資料
型號: FT2232HL-TRAY
廠商: FTDI, Future Technology Devices International Ltd
文件頁數: 25/67頁
文件大?。?/td> 0K
描述: IC USB HS DUAL UART/FIFO 64-LQFP
標準包裝: 160
系列: USBmadeEZ-FIFO,F(xiàn)T-X,X-Chip
特點: USB 至 UART 和(或)FIFO、SPI、I2C、JTAG
通道數: 2,DUART
FIFO's: 4096 字節
規程: RS232,RS422,RS485
電源電壓: 3 V ~ 3.6 V
帶并行端口:
帶自動流量控制功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
供應商設備封裝: 64-LQFP
包裝: 托盤
其它名稱: FT2232HL - TRAY
Copyright 2012 Future Technology Devices International Limited
31
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
4.6 MPSSE Interface Mode Description.
MPSSE Mode is designed to allow the FT2232H to interface efficiently with synchronous serial protocols
such as JTAG, I2C and SPI Bus. It can also be used to program SRAM based FPGAs over USB. The
MPSSE interface is designed to be flexible so that it can be configured to allow any synchronous serial
protocol (industry standard or proprietary) to be implemented using the FT2232H. MPSSE is available on
channel A and channel B.
MPSSE is fully configurable, and is programmed by sending commands down the data stream. These can
be sent individually or more efficiently in packets. MPSSE is capable of a maximum sustained data rate of
30 Mbits/s.
When a channel is configured in MPSSE mode, the IO timing and signals used are shown in Figure 4.7
and Table 4.3 These show timings for CLKOUT=30MHz. CLKOUT can be divided internally to be provide a
slower clock.
Figure 4.7 MPSSE Signal Waveforms
Name
Minimum
Typical
Maximum
Units
Description
t1
33.33
ns
CLKOUT period
t2
15
16.67
ns
CLKOUT high period
t3
15
16.67
ns
CLKOUT low period
t4
1
7.15
ns
CLKOUT to TDI/DO delay
t5
0
ns
TDO/DI hold time
t6
11
TDO/DI setup time
Table 4.3 MPSSE Signal Timings
MPSSE mode is enabled using Set Bit Bang Mode driver command. A hex value of 2 will enable it, and a
hex value of 0 will reset the device. See application note AN2232L-02, “Bit Mode Functions for the
FT2232D” for more details and examples.
The MPSSE command set is fully described in application note AN_108 – “Command Processor For
MPSSE and MCU Host Bus Emulation Modes”.
The following additional application notes are available for configuring the MPSSE :
AN_109 – “Programming Guide for High Speed FTCI2C DLL”
AN_110 – “Programming Guide for High Speed FTCJTAG DLL”
AN_111 – “Programming Guide for High Speed FTCSPI DLL”
相關PDF資料
PDF描述
SC28L92A1A,512 IC UART DUAL W/FIFO 44-PLCC
VI-B5B-IY CONVERTER MOD DC/DC 95V 50W
D38999/20WD19PC CONN RCPT 19POS WALL MNT W/PINS
ATMEGA169PV-8MCHR MCU AVR 16KB FLASH 16MHZ 64QFN
MS27484T16B8PA CONN PLUG 8POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
FT2232HMINIMODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module
FT2232H-MINI-MODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED
FT2232HQ 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64
FT2232HQ_MINI_ MODULE 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
FT2232HQ-4000 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC