參數資料
型號: FT2232HL-TRAY
廠商: FTDI, Future Technology Devices International Ltd
文件頁數: 38/67頁
文件大小: 0K
描述: IC USB HS DUAL UART/FIFO 64-LQFP
標準包裝: 160
系列: USBmadeEZ-FIFO,F(xiàn)T-X,X-Chip
特點: USB 至 UART 和(或)FIFO、SPI、I2C、JTAG
通道數: 2,DUART
FIFO's: 4096 字節
規程: RS232,RS422,RS485
電源電壓: 3 V ~ 3.6 V
帶并行端口:
帶自動流量控制功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 64-LQFP
供應商設備封裝: 64-LQFP
包裝: 托盤
其它名稱: FT2232HL - TRAY
Copyright 2012 Future Technology Devices International Limited
43
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
WRSTB#
RDSTB#
Figure 4.19 Synchronous Bit-Bang Mode Timing Interface Example
Name
Description
t1
Current pin state is read
t2
RDSTB# is set inactive and data on the paralle I/O pins is read and sent to the USB host.
t3
RDSTB# is set active again, and any pins that are output will change to their new data
t4
1 clock cycle to allow for data setup
t5
WRSTB# goes active. This indicates that the host PC has written new data to the I/O parallel data pins
t6
WRSTB# goes inactive
Table 4.10 Synchronous Bit-Bang Mode Timing Interface Example Timings
WRSTB# = this output indicates when new data has been written to the I/O pins from the Host PC (via
the USB interface).
RDSTB# = this output rising edge indicates when data has been read from the I/O pins and sent to the
Host PC (via the USB interface).
The WRSTB# goes active in t4. The WRSTB# goes active when data is read from the USB RXFIFO (i.e.
sent from the PC). The RDSTB# goes inactive when data is sampled from the pins and written to the USB
TXFIFO (i.e. sent to the PC). The SETUP command to the FT2232H is used to setup the bit-mode. This
command also contains a byte wide data mask to set the direction of each bit. The direction on each pin
doesnt change unless a new SETUP command is used to modify the direction.
The WRSTB# and RDSTB# strobes are only a guide to what may be happening depending on the
direction of the bus. For example if all pins are configured as inputs, it is still necessary to write to these
pins in order to get the FT2232H to read those pins even though the data written will never appear on
the pins.
Signals and data-flow are illustrated in Figure 4.20
USB Rx
FIFO/
Buffer
Parallel I/O
data
Parallel
I/O pins
USB
WRSTB#
RDSTB#
USB Tx
FIFO/
Buffer
Figure 4.20 Bit-bang Mode Dataflow Illustration Diagram.
相關PDF資料
PDF描述
SC28L92A1A,512 IC UART DUAL W/FIFO 44-PLCC
VI-B5B-IY CONVERTER MOD DC/DC 95V 50W
D38999/20WD19PC CONN RCPT 19POS WALL MNT W/PINS
ATMEGA169PV-8MCHR MCU AVR 16KB FLASH 16MHZ 64QFN
MS27484T16B8PA CONN PLUG 8POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
FT2232HMINIMODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed FT2232H Evaluation Module 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB to serial/FIFO development module
FT2232H-MINI-MODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC,EVALUATION MODULE;FT2232H;USB HI-SPEED
FT2232HQ 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64
FT2232HQ_MINI_ MODULE 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
FT2232HQ-4000 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC