參數資料
| 型號： | ISL12022MIBZ-TR5421 |
| 廠商： | Intersil |
| 文件頁數： | 13/31頁 |
| 文件大小： | 0K |
| 描述： | IC RTC/CALENDAR TEMP SNSR 20SOIC |
| 應用說明： | Addressing Power Issues in Real Time Clock Appls |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/日歷 |
| 特點： | 警報器，夏令時，閏年，SRAM |
| 存儲容量： | 128B |
| 時間格式： | HH:MM:SS（12/24 小時） |
| 數據格式： | YY-MM-DD-dd |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 電壓 - 電源，電池： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 20-SOIC |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
ISL12022MR5421
20
FN7576.3
June 7, 2012
A write to both bytes in this register will only change the 3 MSB’s
(TSE, BTSE, BTSR), and the 5 LSB’s will remain the same as set
at the factory.
TEMPERATURE SENSOR ENABLED BIT (TSE)
This bit enables the Temperature Sensing operation, including the
temperature sensor, A/D converter and FATR/FDTR register
adjustment. The default mode after power-up is disabled: (TSE = 0).
To enable the operation, TSE should be set to 1. (TSE = 1). When
temp sense is disabled, the initial values for IATR and IDTR registers
are used for frequency control.
When TSE is set to 1, the temperature conversion cycle begins and
will end when two temperature conversions are completed. The
average of the two conversions is in the TEMP registers.
TEMP SENSOR CONVERSION IN BATTERY MODE BIT
(BTSE)
This bit enables the Temperature Sensing and Correction in battery
mode. BTSE = 0 (default) no conversion, Temp Sensing or
Compensation in battery mode. BTSE = 1 indicates Temp Sensing
and Compensation enabled in battery mode. The BTSE is disabled
when the battery voltage is lower than 2.7V. No temperature
compensation will take place with VBAT < 2.7V.
FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT (BTSR)
This bit controls the frequency of Temp Sensing and Correction.
BTSR = 0 default mode is every 10 minutes, BTSR = 1 is every
1.0 minute. Note that BTSE has to be enabled in both cases. See
Table 16.
The temperature measurement conversion time is the same for
battery mode as for VDD mode, approximately 22ms. The battery
mode current will increase during this conversion time to
typically 68A. The average increase in battery current is much
lower than this due to the small duty cycle of the ON-time versus
OFF-time for the conversion.
To figure the average increase in battery current, we take the
change in current times the duty cycle. For the 1 minute
temperature period, the average current is expressed in Equation
For the 10 minute temperature period the average current is
expressed in Equation 2:
If the application has a stable temperature environment that
doesn’t change quickly, the 10 minute option will work well and
the backup battery lifetime impact is minimized. If quick
temperature variations are expected (multiple cycles of more
than 10° within an hour), then the 1 minute option should be
considered and the slightly higher battery current figured into
overall battery life.
GAIN FACTOR OF AT BIT (BETA<4:0>)
Beta is specified to take care of the Cm variations of the crystal.
Most crystals specify Cm around 2.2fF. For example, if Cm > 2.2fF,
the actual AT steps may reduce from 1ppm/step to approximately
0.80ppm/step. Beta is then used to adjust for this variation and
restore the step size to 1ppm/step.
BETA values are limited in the range from 01000 to 11111, as
settings as follows:
BETA VALUES = (AT(max) - AT (min))/63, where:
AT(max) = FOUT in ppm (at AT = 00H) and
AT(min) = FOUT in ppm (at AT = 3FH).
The BETA VALUES result is indexed in the right hand column and
the resulting Beta factor (for the register) is in the same row in
the left column.
The ISL12022MR5421 has a preset BETA value corresponding to
the crystal in the module. This value is recalled on initial power-
up and is preset in device production. It is READ ONLY and
cannot be overwritten by the user.
TABLE 16. FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT
BTSE
BTSR
TC PERIOD IN
BATTERY MODE
00
OFF
01
OFF
10
10 Minutes
11
1 Minute
ΔI
BAT
0.022s
60s
------------------
=
68
μA 250nA
=
×
(EQ. 1)
ΔI
BAT
0.022s
600s
------------------
=
68
μA 25nA
=
×
(EQ. 2)
TABLE 17. BETA VALUES
BETA<4:0>
AT STEP ADJUSTMENT
01000
0.5000
00111
0.5625
00110
0.6250
00101
0.6875
00100
0.7500
00011
0.8125
00010
0.8750
00001
0.9375
00000
1.0000
10000
1.0625
10001
1.1250
10010
1.1875
10011
1.2500
10100
1.3125
10101
1.3750
10110
1.4375
10111
1.5000
11000
1.5625
11001
1.6250
相關PDF資料 |
PDF描述 |
|---|---|
| VI-BNJ-MW-B1 | CONVERTER MOD DC/DC 36V 100W |
| VI-BNJ-MV | CONVERTER MOD DC/DC 36V 150W |
| ISL23318UFUZ-T7A | IC DGTL POT 1CH 50K 10MSOP |
| ISL12029IVAZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
| ISL12029IV30AZ | IC RTC/CALENDAR EEPROM 14-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL12022MR5421 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM, Integrated 5ppm |
| ISL12022M-R5421 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:High-Accuracy RTC Modules, Feature-Rich RTCs |
| ISL12023 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Power RTC with Battery-Backed SRAM and Embedded Temp Compensation ±5ppm with Auto Daylight Saving |
| ISL12023IVZ | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/TEMP COM 14 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
| ISL12023IVZ-T | 功能描述:實時時鐘 REAL TIME CLK/CLNDR W/TEMP COM 14 L RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。