- 您現在的位置：買賣IC網 > PDF目錄2002 > ISL98003CNZ-165 (Intersil)IC AFE 3CH 8BIT 165MHZ 80EPTQFP PDF資料下載
參數資料
| 型號： | ISL98003CNZ-165 |
| 廠商： | Intersil |
| 文件頁數： | 20/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AFE 3CH 8BIT 165MHZ 80EPTQFP |
| 標準包裝： | 119 |
| 位數： | 8 |
| 通道數： | 3 |
| 功率（瓦特）： | 1.1W |
| 電壓 - 電源，模擬： | 1.8V，3.3V |
| 電壓 - 電源，數字： | 1.65 V ~ 2 V |
| 封裝/外殼： | 80-TQFP 裸露焊盤 |
| 供應商設備封裝： | 80-TQFP-EP（12x12） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
27
FN6760.0
September 12, 2008
Crystal Oscillator
An external 12MHz to 27MHz crystal supplies the low-jitter
reference clock to the DPLL. The absolute frequency of this
crystal within this range is unimportant, as is the crystal’s
temperature coefficient, allowing use of less expensive,
lower-grade crystals.
As an alternative to a crystal, the XTALIN pin can be driven
with a 3.3V CMOS-level external clock source at any
frequency between 12MHz and 27MHz. The ISL98003’s
jitter specification assumes a low-jitter crystal source. If the
external clock source has increased jitter, the sample clock
generated by the DPLL may exhibit increased jitter as well.
EMI Considerations
There are two possible sources of EMI on the ISL98003, as
follows.
CRYSTAL OSCILLATOR
The EMI from the crystal oscillator is negligible. This is due to
an amplitude-regulated, low voltage sine wave oscillator circuit,
instead of the typical high-gain square wave inverter-type
oscillator, so there are no harmonics. The crystal oscillator is
not a significant source of EMI.
DIGITAL OUTPUT SWITCHING
This is the largest potential source of EMI. However, the EMI is
determined by the PCB layout and the loading on the databus.
The way to control this is to put series resistors on the output of
all the digital pins (as our demo board and reference circuits
show). These resistors should be as large as possible, while
still meeting the setup and hold timing requirements of the
scaler. We recommend starting with 22
Ω. If the databus is
heavily loaded (long traces, many other part on the same bus),
this value may need to be reduced. If the databus is lightly
loaded, it may be increased.
Intersil’s recommendations to minimize EMI are:
Minimize the databus trace length
Minimize the databus capacitive loading.
If EMI is a problem in the final design, increase the value of the
digital output series resistors to reduce slew rates on the bus.
This can only be done as long as the scaler’s setup and hold
timing requirements continue to be met.
Standby Mode
The ISL98003 can be placed into a low power standby mode
by writing a 0x0F to register 0x2C, powering down the triple
ADCs, the DPLL, and most of the internal clocks.
To allow input monitoring and mode detection during
power-down, the following blocks remain active:
Serial interface (including the crystal oscillator) to enable
register read/write activity
Activity and polarity detect functions (registers 0x01 and
0x02)
The HSYNCOUT and VSYNCOUT pins (for mode detection)
Initialization
The ISL98003 initializes with default register settings for an
AC-coupled, RGB input on the VGA1 channel.
Reset
The ISL98003 has a Power On Reset (POR) function that
resets the chip to its default state when power is initially
applied, including resetting all the registers to their default
settings as described in the “Register Listing” on page 10.
The POR function takes 512k Crystal clocks (~21ms at
25MHz) to complete. The external RESET pin duplicates the
reset function of the POR without having to cycle the power
supplies. The RESET pin does not need to be used in
normal operation and can be tied high.
ISL98003 Serial Communication
Overview
The ISL98003 uses a 2-wire serial bus for communication
with its host. SCL is the Serial Clock line, driven by the host,
and SDA is the Serial Data line, which can be driven by all
devices on the bus. SDA is open drain to allow multiple
devices to share the same bus simultaneously.
Communication is accomplished in three steps:
1. The Host selects the ISL98003 it wishes to communicate
with.
2. The Host writes the initial ISL98003 Configuration
Register address it wishes to write to or read from.
3. The Host writes to or reads from the ISL98003’s
Configuration Register. The ISL98003’s internal address
pointer auto increments, so to read registers 0x00
through 0x1B, for example, one would write 0x00 in
Step 2, then repeat Step 3 (28) times, with each read
returning the next register value.
The ISL98003 has a 7-bit address (1001100) on the serial
bus.
The bus is nominally inactive, with SDA and SCL high.
Communication begins when the host issues a START
command by taking SDA low while SCL is high (Figure 3).
The ISL98003 continuously monitors the SDA and SCL lines
for the start condition and will not respond to any command
until this condition has been met. The host then transmits the
7-bit serial address plus a R/W bit, indicating if the next
transaction will be a Read (R/W = 1) or a Write (R/W = 0). If
the address transmitted matches that of any device on the
bus, that device must respond with an ACKNOWLEDGE
(see Figure 4).
ISL98003
相關PDF資料 |
PDF描述 |
|---|---|
| ISLA118P50IRZ | IC ADC 8BIT SPI/SRL 500M 72QFN |
| ISLA212P20IRZ | IC ADC 12BIT SRL/SPI 72QFN |
| ISLA214S50IR1Z | IC ADC |
| ISLA222P13IRZ | IC ADC 12BIT SRL/SPI 72QFN |
| ISLA224S25IR1Z | IC ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL98003CNZ-165S2733 | 制造商:Intersil Corporation 功能描述:TANGTOP ISL98003CNZ-T165 W/BUSINESS TRACKING REQUIREMENTS - Trays |
| ISL98003CNZ-EVALZ | 功能描述:EVAL BOARD FOR ISL98003CNZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL98003INZ-110 | 功能描述:IC AFE 3CH 8BIT 110MHZ 80EPTQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模擬前端 (AFE) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:- 通道數:2 功率（瓦特）:- 電壓 - 電源，模擬:3 V ~ 3.6 V 電壓 - 電源，數字:3 V ~ 3.6 V 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:帶卷 (TR) |
| ISL98003INZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL98003INZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL98012IUZ | 功能描述:直流/直流開關轉換器 1.8V INPUT PWM STP UPG 10LD RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。