- 您現在的位置：買賣IC網 > PDF目錄2002 > ISL98003CNZ-165 (Intersil)IC AFE 3CH 8BIT 165MHZ 80EPTQFP PDF資料下載
參數資料
| 型號： | ISL98003CNZ-165 |
| 廠商： | Intersil |
| 文件頁數： | 30/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AFE 3CH 8BIT 165MHZ 80EPTQFP |
| 標準包裝： | 119 |
| 位數： | 8 |
| 通道數： | 3 |
| 功率（瓦特）： | 1.1W |
| 電壓 - 電源，模擬： | 1.8V，3.3V |
| 電壓 - 電源，數字： | 1.65 V ~ 2 V |
| 封裝/外殼： | 80-TQFP 裸露焊盤 |
| 供應商設備封裝： | 80-TQFP-EP（12x12） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁
8
FN6760.0
September 12, 2008
CLAMPIN
Digital 3.3V input.When this input is high and external CLAMP is selected, connects the selected channels inputs to the
clamp DAC.
CLOCKINVIN
Digital 3.3V input. When high, changes the pixel sampling phase by 180°. Toggle at frame rate during VSYNC to allow 2x
undersampling to sample odd and even pixels on sequential frames. Tie to DGND if unused.
TESTOUT
3.3V digital output. A delayed version of internal COAST or CLAMP when selected.
RESET
Digital 3.3V input, active low, 70k
Ω pull-up to VD. Take low for at least 1s and then high again to reset the ISL98003. This
pin is not necessary for normal use and may be tied directly to the VD supply.
XTALIN
Analog input. Connect to external 12MHz to 27MHz crystal and load capacitor (see crystal spec for recommended loading).
Typical oscillation amplitude is 1.0VP-P centered around 0.5V.
XTALOUT
Analog output. Connect to external 12MHz to 27MHz crystal and load capacitor (see crystal spec for recommended
loading). Typical oscillation amplitude is 1.0VP-P centered around 0.5V.
XCLKOUT
3.3V digital output. Buffered crystal clock output at fXTAL or fXTAL/2. May be used as system clock for other system
components.
SCL
Digital input, 5V tolerant, 500mV hysteresis. Serial data clock for 2-wire interface.
SDA
Bidirectional Digital I/O, open drain, 5V tolerant. Serial data I/O for 2-wire interface.
EXTCLKIN
Digital 3.3V input. External clock input for AFE.
R[7:0]
3.3V digital output. 8-bit Red channel pixel data.
G[7:0]
3.3V digital output. 8-bit Green channel pixel data.
B[7:0]
3.3V digital output. 8-bit Blue channel pixel data.
DATACLK
3.3V digital output. Data (pixel) clock output.
DATACLK
3.3V digital output. Inverse of DATACLK.
HSOUT
3.3V digital output. HSYNC output aligned with pixel data. Use this output to frame the digital output data. This output is
always purely horizontal sync (without any composite sync signals).
HSYNCOUT
3.3V digital output. Buffered HSYNC (or SOG or CSYNC) output. This is typically used for measuring HSYNC period. This
output will pass composite sync signals and Macrovision signals if present on HSYNCIN or SOGIN.
VSYNCOUT
3.3V digital output. Buffered VSYNC output. For composite sync signals, this output will be asserted for the duration of the
disruption of the normal HSYNC pattern. This is typically used for measuring VSYNC period.
INT
Digital output, open drain, 5V tolerant. Interrupt output indicating mode change or command execution status. Pull high
with a 4.7k resistor.
DE
3.3V digital output. High when there is valid video data, low during horizontal and vertical blanking periods.
FIELD
3.3V digital output. For interlaced video, this output will changes states to indicate whether current field is even or odd.
Polarity is determined by configuration register.
VA3.3
Power supply for the analog section. Connect to a 3.3V supply and bypass each pin to GND with 0.1F.
VA1.8
Power supply for the analog section. Connect to a 1.8V supply and bypass each pin to GND with 0.1F.
VPLLA3.3
Power supply for the analog PLL section. Connect to a 3.3V supply and bypass to GND with 0.1F.
GND
Ground return connected to exposed pad.
VD3.3
Power supply for all digital I/Os. Connect to a 3.3V supply and bypass each pin to GND with 0.1F.
VD1.8
Power supply for digital core logic. Connect to a 1.8V supply and bypass each pin to GND with 0.1F.
VADCD1.8
Power supply for the digital ADC section. Connect to a 1.8V supply and bypass to GND with 0.1F.
VPLLD1.8
Power supply for the digital PLL section. Connect to a 1.8V supply and bypass to GND with 0.1F.
DTEST1, 2, 3, 4, 5
For production use only. Tie to GND.
Pin Descriptions (Continued)
SYMBOL
DESCRIPTION
ISL98003
相關PDF資料 |
PDF描述 |
|---|---|
| ISLA118P50IRZ | IC ADC 8BIT SPI/SRL 500M 72QFN |
| ISLA212P20IRZ | IC ADC 12BIT SRL/SPI 72QFN |
| ISLA214S50IR1Z | IC ADC |
| ISLA222P13IRZ | IC ADC 12BIT SRL/SPI 72QFN |
| ISLA224S25IR1Z | IC ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL98003CNZ-165S2733 | 制造商:Intersil Corporation 功能描述:TANGTOP ISL98003CNZ-T165 W/BUSINESS TRACKING REQUIREMENTS - Trays |
| ISL98003CNZ-EVALZ | 功能描述:EVAL BOARD FOR ISL98003CNZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL98003INZ-110 | 功能描述:IC AFE 3CH 8BIT 110MHZ 80EPTQFP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模擬前端 (AFE) 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:- 通道數:2 功率（瓦特）:- 電壓 - 電源，模擬:3 V ~ 3.6 V 電壓 - 電源，數字:3 V ~ 3.6 V 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:帶卷 (TR) |
| ISL98003INZ-EVALZ | 功能描述:EVALUATION BOARD FOR ISL98003INZ RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| ISL98012IUZ | 功能描述:直流/直流開關轉換器 1.8V INPUT PWM STP UPG 10LD RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。