31 FN7853.1 June 17, 2011 A/D Evaluation Platform Intersil offers an A/D Evaluation platform which can be used to evaluate any of Inte" />
參數資料
型號: ISLA222P13IRZ
廠商: Intersil
文件頁數: 25/33頁
文件大?。?/td> 0K
描述: IC ADC 12BIT SRL/SPI 72QFN
標準包裝: 1
系列: FemtoCharge™
位數: 12
采樣率(每秒): 130M
數據接口: 串行,SPI?
轉換器數目: 2
功率耗散(最大): 697mW
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 72-VFQFN 裸露焊盤
供應商設備封裝: 72-QFN(10x10)
包裝: 托盤
輸入數目和類型: *
ISLA222P
31
FN7853.1
June 17, 2011
A/D Evaluation Platform
Intersil offers an A/D Evaluation platform which can be used to
evaluate any of Intersil’s high speed A/D products. The platform
consists of a FPGA based data capture motherboard and a family
of A/D daughtercards. This USB based platform allows a user to
quickly evaluate the A/D’s performance at a user’s specific
application frequency requirements. More information is
available at
Layout Considerations
Split Ground and Power Planes
Data converters operating at high sampling frequencies require
extra care in PC board layout. Many complex board designs
benefit from isolating the analog and digital sections. Analog
supply and ground planes should be laid out under signal and
clock inputs. Locate the digital planes under outputs and logic
pins. Grounds should be joined under the chip.
Clock Input Considerations
Use matched transmission lines to the transformer inputs for the
analog input and clock signals. Locate transformers and
terminations as close to the chip as possible.
Exposed Paddle
The exposed paddle must be electrically connected to analog
ground (AVSS) and should be connected to a large copper plane
using numerous vias for optimal thermal performance.
Bypass and Filtering
Bulk capacitors should have low equivalent series resistance.
Tantalum is a good choice. For best performance, keep ceramic
bypass capacitors very close to device pins. Longer traces will
increase inductance, resulting in diminished dynamic
performance and accuracy. Make sure that connections to
ground are direct and low impedance. Avoid forming ground
loops.
LVDS Outputs
Output traces and connections must be designed for 50
Ω (100Ω
differential) characteristic impedance. Keep traces direct and
minimize bends where possible. Avoid crossing ground and
power-plane breaks with signal traces.
LVCMOS Outputs
Output traces and connections must be designed for 50
Ω
characteristic impedance.
Unused Inputs
Standard logic inputs (RESETN, CSB, SCLK, SDIO and SDO) which
will not be operated do not require connection to ensure optimal
A/D performance. These inputs can be left floating if they are not
used. Tri-level inputs (NAPSLP) accept a floating input as a valid
state, and therefore should be biased according to the desired
functionality.
Definitions
Analog Input Bandwidth is the analog input frequency at which
the spectral output power at the fundamental frequency (as
determined by FFT analysis) is reduced by 3dB from its full-scale
low-frequency value. This is also referred to as Full Power
Bandwidth.
Aperture Delay or Sampling Delay is the time required after the
rise of the clock input for the sampling switch to open, at which
time the signal is held for conversion.
Aperture Jitter is the RMS variation in aperture delay for a set of
samples.
Clock Duty Cycle is the ratio of the time the clock wave is at logic
high to the total time of one clock period.
Differential Non-Linearity (DNL) is the deviation of any code width
from an ideal 1 LSB step.
FIGURE 49. VCM_OUT OUTPUT
Equivalent Circuits (Continued)
VCM
AVDD
0.94V
+
相關PDF資料
PDF描述
ISLA224S25IR1Z IC ADC
KAD2708C-27Q68 IC ADC 8BIT 275MSPS PAR 68-QFN
KAD2708L-27Q68 IC ADC 8BIT 275MSPS PAR 68-QFN
KAD2710C-27Q68 IC ADC 10BIT 275MSPS PAR 68-QFN
KAD2710L-21Q68 IC ADC 10BIT 210MSPS SGL 68-QFN
相關代理商/技術參數
參數描述
ISLA222P20 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC
ISLA222P20IRZ 功能描述:IC ADC 12BIT SRL/SPI 72QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:FemtoCharge™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 位數:10 采樣率(每秒):357k 數據接口:DSP,MICROWIRE?,QSPI?,串行,SPI? 轉換器數目:1 功率耗散(最大):830µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP(3x3) 包裝:剪切帶 (CT) 輸入數目和類型:2 個單端,單極;2 個單端,雙極;1 個差分,單極;1 個差分,雙極 產品目錄頁面:1396 (CN2011-ZH PDF) 其它名稱:MAX1395ETB+TCT
ISLA222P25 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 14-Bit, 250MSPS/200MSPS/130MSPS ADC
ISLA222P25IRZ 制造商:Intersil Corporation 功能描述:12-BIT 250MSPS DUAL ADC, 72-PIN QFN - Trays 制造商:Intersil Corporation 功能描述:IC ADC 12BIT SRL/SPI 72QFN 制造商:Intersil 功能描述:12-BIT 250MSPS DL AD C 72-PIN
ISLA222S 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Dual 12-Bit, 250/200/125 MSPS JESD204B High Speed Serial Output ADC