參數資料
型號： ISP1561
廠商： NXP Semiconductors N.V.
英文描述： ISP1561BM
中文描述： ISP1561BM
文件頁數： 63/102頁
文件大?。?/td> 2875K
代理商： ISP1561
Philips Semiconductors
ISP1561
USB PCI host controller
Product data
Rev. 01 — 06 February 2003
63 of 102
9397 750 10015
Koninklijke Philips Electronics N.V. 2003. All rights reserved.
8
PPS
On read
—PortPowerStatus:
This bit reflects the port power
status, regardless of the type of power switching implemented.
This bit is cleared if an overcurrent condition is detected. The HCD
can set this bit by writing SetPortPower or SetGlobalPower. The
HCD can clear this bit by writing ClearPortPower or
ClearGlobalPower. PowerSwitchingMode and
PortPowerControlMask[NDP] determine which power control
switches are enabled. In the global switching mode
(PowerSwitchingMode = 0), only Set/ClearGlobalPower controls
this bit. In the per-port power switching
(PowerSwitchingMode = 1), if the PortPowerControlMask[NDP] bit
for the port is set, only Set/ClearPortPower commands are
enabled. If the mask is not set, only Set/ClearGlobalPower
commands are enabled.
When port power is disabled, CCS (CurrentConnectStatus), PES
(PortEnableStatus), PSS (PortSuspendStatus) and PRS
(PortResetStatus) should be reset.
0 —
port power is OFF
1 —
port power is ON
On write—
SetPortPower:
The HCD can write logic 1 to set the
PPS (PortPowerStatus) bit. Writing logic 0 has no effect.
Remark:
This bit always reads logic1 if power switching is not
supported.
reserved
On read—
PortResetStatus:
When this bit is set by a write to
SetPortReset, port reset signaling is asserted. When reset is
completed and PRSC (PortResetStatusChange) is set, this bit is
cleared.
7 to 5
4
-
PRS
0 —
port reset signal is not active
1 —
port reset signal is active
On write—
SetPortReset:
The HCD can set the port reset
signaling by writing a 1 to this bit. Writing a 0 has no effect. If CCS
is cleared, this write does not set PRS (PortResetStatus) but
instead sets CCS. This informs the driver that it attempted to reset
a disconnected port.
On read—
PortOverCurrentIndicator:
This bit is valid only when
the Root Hub is configured to show overcurrent conditions are
reported on a per-port basis. If the per-port overcurrent reporting is
not supported, this bit is set to logic 0. If cleared, all power
operations are normal for this port. If set, an overcurrent condition
exists on this port.
3
POCI
0 —
no overcurrent condition
1 —
overcurrent condition detected
On write—
ClearSuspendStatus:
The HCD can write logic 1 to
initiate a resume. Writing logic 0 has no effect. A resume is
initiated only if PSS (PortSuspendStatus) is set.
Table 85:
Bit
HCRhPortStatus[1:4] register: bit description
…continued
Symbol
Description
相關PDF資料
PDF描述
ISP1561BM ISP1561BM
ISP1562 Hi-Speed Universal Serial Bus PCI Host Controller
ISP1562BE Hi-Speed Universal Serial Bus PCI Host Controller
ISP1581 Universal Serial Bus 2.0 high-speed interface device
ISP1581BD Universal Serial Bus 2.0 high-speed interface device
相關代理商/技術參數
參數描述
ISP1561 HI-SPEED USB H 制造商:NXP Semiconductors 功能描述:
ISP1561BM 制造商:NXP Semiconductors 功能描述:
ISP1561BM,518 功能描述:USB 接口集成電路 USB 2.0 HOST CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1561BM,551 功能描述:USB 接口集成電路 USB 2.0 HOST CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1561BM,557 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*