參數資料
型號： K9F1208Q0B-P
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： 64M x 8 Bit NAND Flash Memory
中文描述： 6400 × 8位NAND閃存
文件頁數： 35/45頁
文件大?。?/td> 767K
代理商： K9F1208Q0B-P
FLASH MEMORY
35
K9F1208U0B
K9F1208D0B
Advance
Figure 12. Block Erase Operation
BLOCK ERASE
The Erase operation is done on a block(16K Byte) basis. Block address loading is accomplished in three cycles initiated by an Erase
Setup command(60h). Only address A
14
to A
25
is valid while A
9
to A
13
is ignored. The Erase Confirm command(D0h) following the
block address loading initiates the internal erasing process. This two-step sequence of setup followed by execution command
ensures that memory contents are not accidentally erased due to external noise conditions.
At the rising edge of WE after the erase confirm command input, the internal write controller handles erase and erase-verify. When
the erase operation is completed, the Write Status Bit(I/O 0) may be checked. Figure 12 details the sequence.
60h
Block Add. : A
14
~ A
25
I/O
X
R/B
Address Input(3Cycle)
I/O
0
Pass
D0h
70h
Fail
t
BERS
Multi-Plane Page Program
Multi-Plane Page Program is an extension of Page Program, which is executed for a single plane with 528 byte page registers. Since
the device is equipped with four memory planes, activating the four sets of 528 byte page registers enables a simultaneous program-
ming of four pages. Partial activation of four planes is also permitted.
After writing the first set of data up to 528 byte into the selected page register, Dummy Page Program command (11h) instead of
actual Page Program (10h) is inputted to finish data-loading of the current plane and move to the next plane. Since no programming
process is involved, R/B remains in Busy state for a short period of time(tDBSY). Read Status command (standard 70h or alternate
71h) may be issued to find out when the device returns to Ready state by polling the Ready/Busy status bit(I/O 6). Then the next set
of data for one of the other planes is inputted with the same command and address sequences. After inputting data for the last plane,
actual True Page Program (10h) instead of dummy Page Program command (11h) must be followed to start the programming pro-
cess. The operation of R/B and Read Status is the same as that of Page Program. Since maximum four pages are programmed
simultaneously, pass/fail status is available for each page when the program operation completes. The extended status bits (I/O1
through I/O 4) are checked by inputting the Read Multi-Plane Status Register. Status bit of I/O 0 is set to "1" when any of the pages
fails. Multi-Plane page Program with "01h" pointer is not supported, thus prohibited.
Figure 13. Four-Plane Page Program
80h
11h
80h
11h
80h
11h
80h
10h
Data
Input
Plane 0
(1024 Block)
Plane 1
(1024 Block)
Plane 2
(1024 Block)
Plane 3
(1024 Block)
Block 0
Block 4
Block 4092
Block 4088
Block 1
Block 5
Block 4093
Block 4089
Block 2
Block 6
Block 4094
Block 4090
Block 3
Block 7
Block 4095
Block 4091
80h
9
~ A
25
528 bytes
I/O
X
R/B
Address &
Data Input
11h
80h
Address &
Data Input
11h
80h
Address &
Data Input
11h
80h
Address &
Data Input
10h
t
DBSY
t
DBSY
t
DBSY
t
PROG
71h
相關PDF資料
PDF描述
K9F1208R0B TV 99C 97#22D 2#8(TWINAX) SKT
K9F1208B0B 64M x 8 Bit NAND Flash Memory
K9F1208U0 64M x 8 Bit NAND Flash Memory
K9F1208U0M-YIB0 64M x 8 Bit NAND Flash Memory
K9F1208U0M-YCB0 64M x 8 Bit NAND Flash Memory
相關代理商/技術參數
參數描述
K9F1208R0B 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:64M x 8 Bit NAND Flash Memory
K9F1208R0C 制造商:未知廠家 制造商全稱:未知廠家 功能描述:三星公司新版本NAND FLASH
K9F1208R0C-J 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:FLASH MEMORY
K9F1208R0C-JIB0000 制造商:Samsung SDI 功能描述:
K9F1208U0 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:64M x 8 Bit NAND Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*