- 您現在的位置：買賣IC網 > PDF目錄15745 > KIT908EINTFC (Freescale Semiconductor)KIT EVAL 908E625 QUAD W/MCU/LIN PDF資料下載
參數資料
| 型號： | KIT908EINTFC |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 21/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL 908E625 QUAD W/MCU/LIN |
| 標準包裝： | 1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
28
Freescale Semiconductor
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Figure 15. Hall-effect Sensor Input Pin Connected to Three Pin Hall-effect Sensor
Interrupts
The Hall-effect sensor input pins are interrupt capable.
How and when an interrupt occurs is dependent on the
operating mode, RUN or Stop.
RUN Mode
In RUN mode the Hall-effect sensor input pin interrupt flag
(HPF) will be set if a state change on the hallflags (HxF) is
detected. The interrupt is maskable with the HPIE bit in the
interrupt mask register. Before enabling the interrupt, the flag
should be cleared in order to prevent a wrong interrupt.
STOP Mode
In STOP mode the Hall-effect sensor input pins are
disabled independent of the state of the HxEN flags.
CYCLIC WAKE-UP
The Hall-effect sensor inputs can be used to wake up the
system. This wake-up function is provided by the cyclic check
wake-up feature of the AWD (Autonomous Watchdog).
If the cyclic check wake-up feature is enabled (AWDCC bit
is set), the AWD switches on the enabled Hall-effect sensor
pins periodically. To ensure that the Hall-effect sensor current
is stabilized after switching on, the inputs are sensed after
~40
μs. If a 1 is detected (IHall sensor >IHSCT) and the
interrupt mask bit HPIE is set, an interrupt is performed. This
wakes up the MCU and starts the main voltage regulator.
The wake-up function via this input is available when all
three conditions exist:
The two-pin Hall-effect sensor input is enabled
(HxEN = 1)
The cyclic wake-up of the AWD is enabled (AWDCC =
1); see Figure 16
The Hall-effect sensor input pin interrupt is enabled
(HPIE = 1)
HxEN
HxF
Sense
Circuitry
V
Hx
GND
Three-Terminal Hall-Effect Sensor
Out
Vs
GND
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6440UTLQZD7+T | IC BATTERY MON SNGL SOT23-6 |
| UVR2F2R2MPD | CAP ALUM 2.2UF 315V 20% RADIAL |
| MAX6440UTLQYD7+T | IC BATTERY MON SNGL SOT23-6 |
| MAX6440UTKSYD7+T | IC BATTERY MON SNGL SOT23-6 |
| MAX6440UTMRSD3+T | IC BATTERY MON SNGL SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KIT-910 | 制造商:Anderson Power Products (APP) 功能描述:KIT |
| KIT912F634EVME | 功能描述:開發板和工具包 - S08 / S12 INTEGRATED DUAL L/H SWIT RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| KIT912H634EVME | 功能描述:開發板和工具包 - S08 / S12 DUAL LOW&HIDE SWITCH EVB RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| KIT912J637EVME | 功能描述:電源管理IC開發工具 BATTERY SENSOR 912J637 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| KIT912S812ECUEVM | 功能描述:電源管理IC開發工具 Single Cylinder S12XS E RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。