- 您現在的位置：買賣IC網 > PDF目錄15745 > KIT908EINTFC (Freescale Semiconductor)KIT EVAL 908E625 QUAD W/MCU/LIN PDF資料下載
參數資料
| 型號： | KIT908EINTFC |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 27/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT EVAL 908E625 QUAD W/MCU/LIN |
| 標準包裝： | 1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
33
908E625
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
Figure 20. BEMF Signal Generation
HALF-BRIDGE OVER-TEMPERATURE
PROTECTION
The half-bridge outputs provide an over-temperature pre-
warning with the HTF in the Interrupt Flag Register (IFR). In
order to protect the outputs against over-temperature, the
high temperature reset must be enabled. If this value is
reached, the part generates a reset and disables all power
outputs.
HALF-BRIDGE OVER-CURRENT PROTECTION
The half-bridges are protected against short to GND, short
to VSUP, and load shorts.
In the event an over-current on the high side is detected,
the high side MOSFETs on all HB high side MOSFETs are
switched off automatically. In the event an over-current on the
low side is detected, all HB low side MOSFETs are switched
off automatically. In both cases the over-current status flag
HB_OCF in the system status register (SYSSTAT) is set.
The over-current status flag is cleared (and the outputs re-
enabled) by writing a Logic [1] to the HB_OCF flag in the
System status register or by reset.
HALF-BRIDGE OVER-VOLTAGE/UNDER-
VOLTAGE
The half-bridge outputs are protected against under-
voltage and over-voltage conditions. This protection is done
by the low and high voltage interrupt circuitry. If one of these
flags (LVF, HVF) is set, the outputs are automatically
disabled.
The over-voltage/under-voltage status flags are cleared
(and the outputs re-enabled) by writing a Logic [1] to the LVF/
HVF flags in the interrupt flag register or by reset. Clearing
this flag is useless as long as a high or low voltage condition
is present.
HALF-BRIDGE CONTROL REGISTER (HBCTL)
H-Bridge Offset Chopping Enable Bit (OFC_EN)
This read/write bit enables offset chopping. Reset clears
the OFC_EN bit.
1 = Offset chopping enabled
0 = Offset chopping disabled
H-Bridges Current Sense Amplification Select Bit (CSA)
This read/write bit selects the current sense amplification
of the H-Bridges. Reset clears the CSA bit.
1 = Current sense amplification set for measuring 0.5 A.
0 = Current sense amplification set for measuring 2.5 A.
Coil Current
Voltage on
1
BEMF Signal
Register Name and Address: HBCTL - $02
Bits
7
6
5
4
3
2
1
0
Read
OFC_EN
CSA
0
CLS2
CLS1
CLS0
Write
Reset
0
相關PDF資料 |
PDF描述 |
|---|---|
| MAX6440UTLQZD7+T | IC BATTERY MON SNGL SOT23-6 |
| UVR2F2R2MPD | CAP ALUM 2.2UF 315V 20% RADIAL |
| MAX6440UTLQYD7+T | IC BATTERY MON SNGL SOT23-6 |
| MAX6440UTKSYD7+T | IC BATTERY MON SNGL SOT23-6 |
| MAX6440UTMRSD3+T | IC BATTERY MON SNGL SOT23-6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KIT-910 | 制造商:Anderson Power Products (APP) 功能描述:KIT |
| KIT912F634EVME | 功能描述:開發板和工具包 - S08 / S12 INTEGRATED DUAL L/H SWIT RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| KIT912H634EVME | 功能描述:開發板和工具包 - S08 / S12 DUAL LOW&HIDE SWITCH EVB RoHS:否 產品:Development Kits 工具用于評估:MC9S12G128 核心:S12 接口類型:CAN, LIN, RS-232, USB 工作電源電壓:5 V 制造商:Freescale Semiconductor |
| KIT912J637EVME | 功能描述:電源管理IC開發工具 BATTERY SENSOR 912J637 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| KIT912S812ECUEVM | 功能描述:電源管理IC開發工具 Single Cylinder S12XS E RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。