參數資料
型號： KSZ8051MNLI
廠商： Micrel Inc
文件頁數： 26/59頁
文件大?。?/td> 0K
描述： TXRX PHY 10/T100 3.3V 32QFN
標準包裝： 640
類型： PHY 收發器
驅動器/接收器數： 1/1
規程： MII
電源電壓： 1.8V，2.5V，3.3V
安裝類型： 表面貼裝
封裝/外殼： 32-VFQFN 裸露焊盤
供應商設備封裝： 32-QFN（5x5）
包裝： 托盤
配用： 576-3865-ND - BOARD EVALUATION FOR KSZ8051MNL
其它名稱： 576-3845
Micrel, Inc.
KSZ8051MNL/RNL
July 2010
32
M9999-070910-1.0
NAND Tree I/O Testing
The following procedure can be used to check for faults on the KSZ8051MNL/RNL digital I/O pin connections to the
board:
1. Enable NAND tree mode by either hardware pin strapping (NAND_Tree#, pin 21) or software (register 16h, bit 5).
2. Use board logic to drive all KSZ8051MNL/RNL NAND tree input pins high.
3. Use board logic to drive each NAND tree input pin, per KSZ8051MNL/RNL NAND Tree pin order, as follow:
a. Toggle the first pin (MDIO) from high to low, and verify the CRS/CONFIG1 pin switch from low to high to
indicate that the first pin is connected properly.
b. Leave the first pin (MDIO) low.
c. Toggle the second pin (MDC) from high to low, and verify the CRS/CONFIG1 pin switch from high to low
to indicate that the second pin is connected properly.
d. Leave the first pin (MDIO) and the second pin (MDC) low.
e. Toggle the third pin from high to low, and verify the CRS/CONFIG1 pin switch from low to high to indicate
that the third pin is connected properly.
f.
Continue with this sequence until all KSZ8051MNL/RNL NAND tree input pins have been toggled.
Each KSZ8051MNL/RNL NAND tree input pin must cause the CRS/CONFIG1 output pin to toggle high-to-low or low-to-
high to indicate a good connection. If the CRS/CONFIG1 pin fails to toggle when the KSZ8051MNL/RNL input pin toggles
from high to low, the input pin has a fault.
Power Management
The KSZ8051MNL/RNL offers the following power management modes:
Power Saving Mode
Power Saving Mode is used to reduce the transceiver power consumption when the cable is unplugged. It is enabled by
writing a one to register 1Fh, bit 10, and is in effect when auto-negotiation mode is enabled and cable is disconnected (no
link).
In this mode, the KSZ8051MNL/RNL shuts down all transceiver blocks, except for transmitter, energy detect and PLL
circuits.
By default, Power Saving Mode is disabled after power-up.
Energy Detect Power Down Mode
Energy Detect Power Down Mode is used to further reduce the transceiver power consumption when the cable is un-
plugged. It is enabled by writing a zero to register 18h, bit 11, and is in effect when auto-negotiation mode is enabled and
cable is disconnected (no link).
In this mode, the KSZ8051MNL/RNL shuts down all transceiver blocks, except for transmitter and energy detect circuits.
Further power consumption is achieved by extending the time interval in between transmissions of link pulses to check for
the presence of a link partner. The periodic transmission of link pulses is needed to ensure two link partners in the same
low power state and with auto MDI/MDI-X disabled can wake up when the cable is connected between them.
By default, Energy Detect Power Down Mode is disabled after power-up.
Power Down Mode
Power Down Mode is used to power down the KSZ8051MNL/RNL device when it is not in use after power-up. It is
enabled by writing a one to register 0h, bit 11.
In this mode, the KSZ8051MNL/RNL disables all internal functions, except for the MII management interface. The
KSZ8051MNL/RNL exits (disables) Power Down Mode after register 0h, bit 11 is set back to zero.
Slow Oscillator Mode
Slow Oscillator Mode is used to disconnect the input reference crystal/clock on XI (pin 9) and select the on-chip slow
oscillator when the KSZ8051MNL/RNL device is not in use after power-up. It is enabled by writing a one to register 11h,
bit 5.
Slow Oscillator Mode works in conjunction with Power Down Mode to put the KSZ8051MNL/RNL device in the lowest
相關PDF資料
PDF描述
KSZ8051RNLI TR TXRX PHY 10/T100 3.3V RMII 32QFN
KSZ8692XPB IC ARM9 PHY 10/100MBPS 400-PBGA
KSZ8695P IC ARM9 W/MMU PHY 10/100 289PBGA
KSZ8695X IC SWITCH 10/100 5PORT 208PQFP
KSZ8721BI TR TXRX PHY 10/100 2.3.3/5V 48-SSOP
相關代理商/技術參數
參數描述
KSZ8051MNLI TR 功能描述:以太網 IC 3.3V, 10Base-T/100Base-TX Physical Layer Transceiver with MII support (32-QFN, Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8051MNLITR 制造商:Micrel 功能描述:Ethernet TXRX PHY 10 T100 3.3V 32 QFN
KSZ8051MNLI-TR 功能描述:1/1 Transceiver Full MII 32-QFN (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:MII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商器件封裝:32-QFN（5x5） 標準包裝:1
KSZ8051MNL-TR 功能描述:1/1 Transceiver Full MII 32-QFN (5x5) 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:過期 類型:收發器 協議:MII 驅動器/接收器數:1/1 雙工:全 接收器滯后:- 數據速率:- 電壓 - 電源:1.8V，2.5V，3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商器件封裝:32-QFN（5x5） 標準包裝:1
KSZ8051MNLU TR 功能描述:以太網 IC Single-Port 10/100BT PHY (Automotive) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*