- 您現在的位置：買賣IC網 > PDF目錄11591 > KSZ8841-16MVLI (Micrel Inc)IC MAC CTRLR 8/16BIT 128-LQFP PDF資料下載
參數資料
| 型號： | KSZ8841-16MVLI |
| 廠商： | Micrel Inc |
| 文件頁數： | 32/105頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MAC CTRLR 8/16BIT 128-LQFP |
| 標準包裝： | 90 |
| 控制器類型： | 以太網控制器，MAC |
| 接口： | 總線 |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-LQFP（14x14） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-1632-ND - BOARD EVALUATION KSZ8841-16MVL |
| 其它名稱： | 576-2114 KSZ8841-16MVLI-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁
Micrel, Inc.
KSZ8841-16/32 MQL/MVL/MBL
October 2007
32
M9999-102207-1.6
LinkMD Cable Diagnostics
The KSZ8841M LinkMD uses time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems
such as open circuits, short circuits, and impedance mismatches.
LinkMD works by sending a pulse of known amplitude and duration down the MDI and MDI-X pairs and then analyzes the
shape of the reflected signal. Timing the pulse duration gives an indication of the distance to the cabling fault with a
maximum distance of 200m and an accuracy of +/–2m. Internal circuitry displays the TDR information in a user-readable
digital format in register P1VCT[8:0].
Note: cable diagnostics are only valid for copper connections – fiber-optic operation is not supported.
Access
LinkMD is initiated by accessing register P1VCT, the LinkMD Control/Status register, in conjunction with register P1CR4,
the 100BASE-TX PHY Controller register.
Usage
LinkMD can be run at any time by ensuring that Auto-MDIX has been disabled. To disable Auto-MDIX, write a ‘1’ to
P1CR4[10] to enable manual control over the pair used to transmit the LinkMD pulse. The self-clearing cable diagnostic
test enable bit, P1VCT[15], is set to ‘1’ to start the test on this pair.
When bit P1VCT[15] returns to ‘0’, the test is complete. The test result is returned in bits P1VCT[14:13] and the distance
is returned in bits P1VCT[8:0]. The cable diagnostic test results are as follows:
00 = Valid test, normal condition
01 = Valid test, open circuit in cable
10 = Valid test, short circuit in cable
11 = Invalid test, LinkMD failed
If P1VCT[14:13]=11, this indicates an invalid test, and occurs when the KSZ8841M is unable to shut down the link
partner. In this instance, the test is not run, as it is not possible for the KSZ8841M to determine if the detected signal is a
reflection of the signal generated or a signal from another source.
Cable distance can be approximated by the following formula:
P1VCT[8:0] x 0.4m for port 1 cable distance
This constant may be calibrated for different cabling conditions, including cables with a velocity of propagation that varies
significantly from the norm.
Media Access Control (MAC) Operation
The KSZ8841M strictly abides by IEEE 802.3 standards to maximize compatibility.
Inter Packet Gap (IPG)
If a frame is successfully transmitted, then the minimum 96-bit time for IPG is measured between two consecutive
packets. If the current packet is experiencing collisions, the minimum 96-bit time for IPG is measured from carrier sense
(CRS) to the next transmit packet.
Back-Off Algorithm
The KSZ8841M implements the IEEE standard 802.3 binary exponential back-off algorithm in half-duplex mode. After 16
collisions, the packet is dropped.
Late Collision
If a transmit packet experiences collisions after 512 bit times of the transmission, the packet is dropped.
Flow Control
The KSZ8841M supports standard 802.3x flow control frames on both transmit and receive sides.
On the receive side, if the KSZ8841M receives a pause control frame, the KSZ8841M will not transmit the next normal
frame until the timer, specified in the pause control frame, expires. If another pause frame is received before the current
timer expires, the timer will be updated with the new value in the second pause frame. During this period (while it is flow
controlled), only flow control packets from the KSZ8841M are transmitted.
On the transmit side, the KSZ8841M has intelligent and efficient ways to determine when to invoke flow control. The flow
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8842-16MBL | IC MAC CTLR 2PORT ETH 100-LFBGA |
| PIC16F630-E/P | IC MCU FLASH 1KX14 14DIP |
| V72A48C400BF | CONVERTER MOD DC/DC 48V 400W |
| VNC2-48L1B-REEL | IC USB HOST/DEVICE CTRL 48-LQFP |
| V72A48C400BL3 | CONVERTER MOD DC/DC 48V 400W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8841-16MVLI TR | 功能描述:以太網 IC Single Ethernet Port + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8841-32MQL | 功能描述:以太網 IC Single Ethernet Port + Generic (32-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8841-32MVL | 功能描述:以太網 IC Single Ethernet Port + Generic (32-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8841-32MVLI | 功能描述:以太網 IC Single Ethernet Port + Generic (32-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8841P | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Ethernet MAC Controller with PCI Interface |
發布緊急采購，3分鐘左右您將得到回復。