- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8993FL (Micrel Inc)IC CONV MED 10/100 SGL 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8993FL |
| 廠商： | Micrel Inc |
| 文件頁數： | 30/100頁 |
| 文件大小： | 0K |
| 描述： | IC CONV MED 10/100 SGL 128PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 其它名稱： | 576-1035 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁
Micrel, Inc.
KS8993F/FL
June 2009
35
M9999-062509
hbwhelp@micrel.com or (408) 955-1690
The MII (Media Independent Interface) is specified by the IEEE 802.3 committee and provides a common interface
between physical layer and MAC layer devices.
The MII Interface provided by the KS8993F is connected to the
device’s third MAC. The interface contains two distinct groups of signals: one for transmission and the other for
reception. The following table describes the signals used in the MII interface.
Table 3: MII Signals
KS8993F PHY mode connections
KS8993F MAC mode connections
External MAC
signals
KS8993F PHY
signals
Pin Description
External PHY
signals
KS8993F MAC
signals
MTXEN
SMTXEN
Transmit enable
MTXEN
SMRXDV
MTXER
SMTXER
Transmit error
MTXER
(not used)
MTXD3
SMTXD[3]
Transmit data bit 3
MTXD3
SMRXD[3]
MTXD2
SMTXD[2]
Transmit data bit 2
MTXD2
SMRXD[2]
MTXD1
SMTXD[1]
Transmit data bit 1
MTXD1
SMRXD[1]
MTXD0
SMTXD[0]
Transmit data bit 0
MTXD0
SMRXD[0]
MTXC
SMTXC
Transmit clock
MTXC
SMRXC
MCOL
SCOL
Collision detection
MCOL
SCOL
MCRS
SCRS
Carrier sense
MCRS
SCRS
MRXDV
SMRXDV
Receive data valid
MRXDV
SMTXEN
MRXER
(not used)
Receive error
MRXER
SMTXER
MRXD3
SMRXD[3]
Receive data bit 3
MRXD3
SMTXD[3]
MRXD2
SMRXD[2]
Receive data bit 2
MRXD2
SMTXD[2]
MRXD1
SMRXD[1]
Receive data bit 1
MRXD1
SMTXD[1]
MRXD0
SMRXD[0]
Receive data bit 0
MRXD0
SMTXD[0]
MRXC
SMRXC
Receive clock
MRXC
SMTXC
The MII interface operates in either PHY mode or MAC mode. The interface is a nibble wide data interface, and
therefore runs at the network bit rate (not encoded). Additional signals on the transmit side indicate when data is
valid or when an error occurs during transmission. Likewise, the receive side has indicators that convey when the data
is valid and without physical layer errors. For half duplex operation, there is a signal that indicates a collision has
occurred during transmission.
Note that the signal MRXER is not provided on the interface for PHY mode operation and the signal MTXER is not
provided on the interface for MAC mode operation. Normally, MRXER would indicate a receive error coming from the
physical layer device. MTXER would indicate a transmit error from the MAC device. These signals are not appropriate
for this configuration. For PHY mode operation, if the device interfacing with the KS8993F has an MRXER pin, it
should be tied low. For MAC mode operation, if the device interfacing with the KS8993F has an MTXER pin, it should
be tied low.
2.6
SNI (7-wire) Interface Operation
The SNI (Serial Network Interface) or 7-wire is compatible with some controllers used for network layer protocol
processing.
In SNI mode, the KS8993F acts like a PHY and the external controller functions as the MAC.
The
KS8993F can interface directly with external controllers using the 7-wire interface. These signals are divided into two
groups, one for transmission and the other for reception. The signals involved are described in the following table.
Table 4: SNI (7-wire) Signals
Pin Description
SNI signals
KS8993F signals
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
| KSZ8995FQ | IC SWITCH 10/100 5PORT 128-PQFP |
| KSZ8995MA | IC SWITCH 10/100 5PORT 128PQFP |
| KSZ8995MI | IC SWITCH 5-PORT 10/100 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8993FL-EVAL | 功能描述:BOARD EVALUATION FOR KSZ8993FL RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| KSZ8993I | 功能描述:以太網 IC 3 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-PQFP, I-TEMP RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993M | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993MA5 | 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8993M-EVAL | 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。