hbwhelp@micrel.com or (408) 955-1690 2.10.1 I
參數資料
型號： KSZ8993FL
廠商： Micrel Inc
文件頁數： 38/100頁
文件大?。?/td> 0K
描述： IC CONV MED 10/100 SGL 128PQFP
標準包裝： 66
系列： *
類型： *
應用： *
安裝類型： 表面貼裝
封裝/外殼： 128-BFQFP
供應商設備封裝： 128-PQFP（14x20）
包裝： 托盤
產品目錄頁面： 1081 (CN2011-ZH PDF)
其它名稱： 576-1035
Micrel, Inc.
KS8993F/FL
June 2009
42
M9999-062509
hbwhelp@micrel.com or (408) 955-1690
2.10.1 I
2C Master Serial Bus Configuration
With an additional I
2C (“2-wire”) EEPROM, the KS8993F can perform more advanced switch features like “broadcast
storm protection” and “rate control” without the need of an external processor.
For KS8993F I
2C Master configuration, the EEPROM stores the configuration data for register 0 to register 109 (as
defined in the KS8993F register map) with the exception of the “Read Only” status registers. After the de-assertion of
reset, the KS8993F will sequentially read in the configuration data for all 110 registers, starting from register 0. The
configuration access time (tprgm) is less than 15 ms, as depicted in the following figure.
Figure 7: KS8993F EEPROM Configuration Timing Diagram
....
RST_N
SCL
SDA
t
prgm<15 ms
The following is a sample procedure for programming the KS8993F with a pre-configured EEPROM:
1.
Connect the KS8993F to the EEPROM by joining the SCL and SDA signals of the respective devices. For the
KS8993F, SCL is pin 97 and SDA is pin 98.
2.
Enable I
2C master mode by setting the KS8993F strap-in pins, PS[1:0] (pins 100 and 101, respectively) to “00”.
3.
Check to ensure that the KS8993F reset signal input, RST_N (pin 67), is properly connected to the external
reset source at the board level.
4.
Program the desired configuration data into the EEPROM.
5.
Place the EEPROM on the board and power up the board.
6.
Assert an active-low reset to the RST_N pin of the KS8993F. After reset is de-asserted, the KS8993F will
begin reading the configuration data from the EEPROM. The KS8993F will check that the first byte read from
the EEPROM is “93”.
If this value is correct, EEPROM configuration will continue.
If not, EEPROM
configuration access is denied and all other data sent from the EEPROM will be ignored by the KS8993F. The
configuration access time (tprgm) is less than 15 ms.
Note: For proper operation, check to ensure that the KS8993F PWRDN input signal (pin 36) is not asserted during the
reset operation. The PWRDN input is active low.
相關PDF資料
PDF描述
KSZ8993MLI IC SWITCH 10/100 3PORT 128-PQFP
KSZ8993ML IC SWITCH 10/100 W/TXRX 128PQFP
KSZ8995FQ IC SWITCH 10/100 5PORT 128-PQFP
KSZ8995MA IC SWITCH 10/100 5PORT 128PQFP
KSZ8995MI IC SWITCH 5-PORT 10/100 128PQFP
相關代理商/技術參數
參數描述
KSZ8993FL-EVAL 功能描述:BOARD EVALUATION FOR KSZ8993FL RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035
KSZ8993I 功能描述:以太網 IC 3 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-PQFP, I-TEMP RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993M 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8993MA5 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝
KSZ8993M-EVAL 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*