- 您現在的位置：買賣IC網 > PDF目錄4594 > KSZ8993M (Micrel Inc)IC SWITCH 10/100 3PORT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8993M |
| 廠商： | Micrel Inc |
| 文件頁數： | 29/85頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 3PORT 128PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 其它名稱： | 576-1037 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Micrel, Inc.
KS8993M/ML/MI
April 2005
35
M9999-041205
IGMP Support
For IGMP support in layer 2, the KS8993M provides two components:
“IGMP” Snooping
The KS8993M will trap IGMP packets and forward them only to the processor (port 3). The IGMP packets are
identified as IP packets (either Ethernet IP packets, or IEEE 802.3 SNAP IP packets) with IP version = 0x4 and
protocol version number = 0x2.
“Multicast Address Insertion” in the Static MAC Table
Once the multicast address is programmed in the Static MAC Table, the multicast session will be trimmed to the
subscribed ports, instead of broadcasting to all ports.
To enable IGMP support, set register 5 bit 6 to “1”. Also, “Special Tagging Mode” needs to be enabled, so that the
processor knows which port the IGMP packet was received on. This is achieved by setting both register 11 bit 0
and register 48 bit 2 to “1.”
Port Mirroring Support
KS8993M supports “Port Mirroring” comprehensively as:
1. “receive only” mirror on a port All the packets received on the port will be mirrored on the sniffer port. For
example, port 1 is programmed to be “receive sniff” and port 3 is programmed to be the “sniffer port”. A packet
received on port 1 is destined to port 2 after the internal lookup. The KS8993M will forward the packet to both port
2 and port 3. The KS8993M can optionally forward even “bad” received packets to the “sniffer port”.
2. “transmit only” mirror on a port All the packets transmitted on the port will be mirrored on the sniffer port.
For example, port 1 is programmed to be “transmit sniff” and port 3 is programmed to be the “sniffer port”. A
packet received on port 2 is destined to port 1 after the internal lookup. The KS8993M will forward the packet to
both port 1 and port 3.
3. “receive and transmit” mirror on two ports All the packets received on port A and transmitted on port B will
be mirrored on the sniffer port. To turn on the “AND” feature, set register 5 bit 0 to “1”. For example, port 1 is
programmed to be “receive sniff”, port 2 is programmed to be “transmit sniff” and port 3 is programmed to be the
“sniffer port”. A packet received on port 1 is destined to port 2 after the internal lookup. The KS8993M will forward
the packet to both port 2 and port 3.
Multiple ports can be selected to be “receive sniff” or “transmit sniff”. And any port can be selected to be the
“sniffer port”. All these per port features can be selected through registers 17, 33 and 49 for ports 1, 2 and 3,
respectively.
IEEE 802.1Q VLAN Support
The KS8993M supports 16 active VLANs out of the 4096 possible VLANs specified in the IEEE 802.1Q
specification. KS8993M provides a 16-entries VLAN Table, which converts the 12-bits VLAN ID (VID) to the 4-bits
Filter ID (FID) for address lookup. If a non-tagged or null-VID-tagged packet is received, the ingress port default
VID is used for lookup. In VLAN mode, the lookup process starts with VLAN Table lookup to determine whether
the VID is valid. If the VID is not valid, the packet will be dropped and its address will not be learned. If the VID is
valid, the FID is retrieved for further lookup. The FID + Destination Address (FID+DA) are used to determine the
destination port. The FID + Source Address (FID+SA) are used for address learning.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8995M | IC SWITCH 10/100 5PORT 128PQFP |
| RSM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
| LFEC6E-3QN208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| LFEC6E-3Q208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| RMM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8993MA5 | 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8993M-EVAL | 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8993MI | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993ML | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993ML-EVAL | 功能描述:以太網開發工具 KSZ8993ML Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。