- 您現在的位置：買賣IC網 > PDF目錄4594 > KSZ8993M (Micrel Inc)IC SWITCH 10/100 3PORT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8993M |
| 廠商： | Micrel Inc |
| 文件頁數： | 32/85頁 |
| 文件大小： | 0K |
| 描述： | IC SWITCH 10/100 3PORT 128PQFP |
| 標準包裝： | 66 |
| 系列： | * |
| 類型： | * |
| 應用： | * |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 其它名稱： | 576-1037 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁
Micrel, Inc.
KS8993M/ML/MI
April 2005
38
M9999-041205
Rate Limiting Support
The KS8993M supports hardware rate limiting independently on the “receive side” and on the “transmit side” on a
per port basis. Rate limiting is supported in both priority and non-priority environment. The rate limit starts from 0
kbps and goes up to the line rate in steps of 32 kbps. The KS8993M uses “one second” as the rate limiting
interval. At the beginning of each interval, the counter is cleared to zero, and the rate limit mechanism starts to
count the number of bytes during the interval.
On the “receive side”, if the number of bytes exceeds the programmed limit, the switch will stop receiving packets
on the port until the “one second” interval expires. Flow control can be enabled to prevent packet loss. If the rate
limit is programmed greater than or equal to 128 kbps and the byte counter is 8 Kbytes below the limit, flow
control will be triggered. If the rate limit is programmed lower than 128 kbps and the byte counter is 2 Kbytes
below the limit, flow control will also be triggered.
On the “transmit side”, if the number of bytes exceeds the programmed limit, the switch will stop transmitting
packets on the port until the “one second” interval expires.
If priority is enabled, the KS8993M can be programmed to support different rate limits for high priority packets and
low priority packets.
Configuration Interface
The KS8993M can operate as both a managed switch and an unmanaged switch.
In unmanaged mode, the KS8993M is typically programmed using an EEPROM. If no EEPROM is present, the
KS8993M is configured using its default register settings. Some defaults settings are configured via strap-in pin
options. The strap-in pins are indicated in the “KS8993M Pin Description and I/O Assignment” table.
I
2C Master Serial Bus Configuration
With an additional I
2C (“2-wire”) EEPROM, the KS8993M can perform more advanced switch features like
“broadcast storm protection” and “rate control” without the need of an external processor.
For KS8993M I
2C Master configuration, the EEPROM stores the configuration data for register 0 to register 109
(as defined in the KS8993M register map) with the exception of the “Read Only” status registers. After the de-
assertion of reset, the KS8993M will sequentially read in the configuration data for all 110 registers, starting from
register 0. The configuration access time (tprgm) is less than 15 ms, as depicted in the following figure.
....
RST_N
SCL
SDA
t
prgm<15 ms
Figure 7. KS8993M EEPROM Configuration Timing Diagram
The following is a sample procedure for programming the KS8993M with a pre-configured EEPROM:
1.
Connect the KS8993M to the EEPROM by joining the SCL and SDA signals of the respective devices. For the
KS8993M, SCL is pin 97 and SDA is pin 98.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8995M | IC SWITCH 10/100 5PORT 128PQFP |
| RSM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
| LFEC6E-3QN208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| LFEC6E-3Q208C | IC FPGA 6.1KLUTS 147I/O 208-PQFP |
| RMM40DTAT | CONN EDGECARD 80POS R/A .156 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8993MA5 | 功能描述:IC SWITCH 10/100 W/TXRX 128PQFP RoHS:是 類別:集成電路 (IC) >> 專用 IC 系列:* 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:調幀器 應用:數據傳輸 安裝類型:表面貼裝 封裝/外殼:400-BBGA 供應商設備封裝:400-PBGA（27x27） 包裝:散裝 |
| KSZ8993M-EVAL | 功能描述:以太網開發工具 KSZ8993M Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8993MI | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993ML | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8993ML-EVAL | 功能描述:以太網開發工具 KSZ8993ML Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。