參數資料
型號： LAN9117
廠商： SMSC Corporation
英文描述： HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
中文描述： 高性能單芯片10/100非PCI以太網控制器
文件頁數： 18/131頁
文件大小： 1531K
代理商： LAN9117
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
Revision 1.1 (05-17-05)
18
SMSC LAN9117
DATASHEET
100,99
,98
General Purpose
I/O data,
nLED1 (Speed
Indicator),
nLED2 (Link &
Activity Indicator),
nLED3 (Full-
Duplex
Indicator
)
.
GPIO[2:0]/
LED[3:1]
IS/O12/
OD12
3
General Purpose I/O data:
These
three general-purpose signals are
fully programmable as either push-
pull output, open-drain output or input
by writing the GPIO_CFG
configuration register in the CSR’s.
They are also multiplexed as GP LED
connections.
GPIO signals are Schmitt-triggered
inputs. When configured as LED
outputs these signals are open-drain.
nLED1 (Speed Indicator).
This
signal is driven low when the
operating speed is 100Mbs, during
auto-negotiation and when the cable
is disconnected. This signal is driven
high only during 10Mbs operation.
nLED2 (Link & Activity Indicator).
This signal is driven low (LED on)
when the LAN9117 detects a valid
link. This signal is pulsed high (LED
off) for 80mS whenever transmit or
receive activity is detected. This
signal is then driven low again for a
minimum of 80mS, after which time it
will repeat the process if TX or RX
activity is detected. Effectively, LED2
is activated solid for a link. When
transmit or receive activity is sensed
LED2 will flash as an activity
indicator.
nLED3 (Full-Duplex Indicator).
This
signal is driven low when the link is
operating in full-duplex mode.
10
RBIAS
RBIAS
AI
1
PLL Bias:
Connect to an external
12.0K ohm 1.0% resistor to ground.
Used for the PLL Bias circuit.
9
Test Pin
ATEST
I
1
This pin must be connected to VDD
for normal operation.
2
Internal Regulator
Power
VREG
P
1
3.3V input for internal voltage
regulator
20,28,
35,
42,48,
55,61,
97
+3.3V I/O Power
VDD_IO
P
8
+3.3V I/O logic power supply pins
19,27,
34,41,
47,54,
60,96
I/O Ground
GND_IO
P
8
Ground for I/O pins
81,85,
89
+3.3V Analog
Power
VDD_A
P
3
+3.3V Analog power supply pins. See
Note 2.1
77,80,
86,88
Analog Ground
VSS_A
P
4
Ground for analog circuitry
Table 2.5 System and Power Signals (continued)
PIN
NO.
NAME
SYMBOL
BUFFER
TYPE
NUM
PINS
DESCRIPTION
相關PDF資料
PDF描述
LAN9117-MD HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
LAN9117-MT HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER
LAN9118 HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER
LAN9118-MD HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER
LAN9118-MT HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER
相關代理商/技術參數
參數描述
LAN9117-MD 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN9117-MT 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
LAN9118 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
LAN9118_05 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
LAN9118_07 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*