- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN9117 (SMSC Corporation) HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER PDF資料下載
參數資料
| 型號： | LAN9117 |
| 廠商： | SMSC Corporation |
| 英文描述： | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| 中文描述： | 高性能單芯片10/100非PCI以太網控制器 |
| 文件頁數： | 99/131頁 |
| 文件大?。?/td> | 1531K |
| 代理商： | LAN9117 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁當前第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
High Performance Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
SMSC LAN9117
99
Revision 1.1 (05-17-05)
DATASHEET
5.4.2
ADDRH—MAC Address High Register
The MAC Address High register contains the upper 16-bits of the physical address of the MAC. The
contents of this register are optionally loaded from the EEPROM at power-on through the EEPROM
Controller if a programmed EEPROM is detected. The least significant byte of this register (bits [7:0])
7-6
BackOff Limit (BOLMT).
The BOLMT bits allow the user to set its back-off limit in a relaxed or
aggressive mode. According to IEEE 802.3, the MAC has to wait for a random number [r] of slot-
times** after it detects a collision, where:
(eq.1)0 <
r
<
K
The exponent K is dependent on how many times the current frame to be transmitted has been retried,
as follows:
(eq.2)K = min
(n,
10) where
n
is the current number of retries.
If a frame has been retried three times, then K = 3 and r= 8 slot-times maximum. If it has been retried
12 times, then K = 10, and r = 1024 slot-times maximum.
An LFSR (linear feedback shift register) 20-bit counter emulates a 20bit random number generator,
from which r is obtained. Once a collision is detected, the number of the current retry of the current
frame is used to obtain K (eq.2). This value of K translates into the number of bits to use from the
LFSR counter. If the value of K is 3, the MAC takes the value in the first three bits of the LFSR counter
and uses it to count down to zero on every slot-time. This effectively causes the MAC to wait eight
slot-times. To give the user more flexibility, the BOLMT value forces the number of bits to be used
from the LFSR counter to a predetermined value as in the table below.
Thus, if the value of K = 10, the MAC will look at the BOLMT if it is 00, then use the lower ten bits of the LFSR
counter for the wait countdown. If the BOLMT is 10, then it will only use the value in the first four bits for the
wait countdown, etc.
**Slot-time = 512 bit times. (See IEEE 802.3 Spec., Secs. 4.2.3.25 and 4.4.2.1)
5
Deferral Check (DFCHK).
When set, enables the deferral check in the MAC. The MAC will abort the
transmission attempt if it has deferred for more than 24,288 bit times. Deferral starts when the
transmitter is ready to transmit, but is prevented from doing so because the CRS is active. Defer time
is not cumulative. If the transmitter defers for 10,000 bit times, then transmits, collides, backs off, and
then has to defer again after completion of back-off, the deferral timer resets to 0 and restarts. When
reset, the deferral check is disabled in the MAC and the MAC defers indefinitely.
4
Reserved
3
Transmitter enable (TXEN).
When set, the MAC’s transmitter is enabled and it will transmit frames
from the buffer onto the cable.
When reset, the MAC’s transmitter is disabled and will not transmit any frames.
2
Receiver Enable (RXEN).
When set (1), the MAC’s receiver is enabled and will receive frames from
the internal PHY.
When reset, the MAC’s receiver is disabled and will not receive any frames from the internal PHY.
1-0
Reserved
Offset:
2
Attribute:
R/W
Default Value:
0000FFFFh
Size:
32 bits
BITS
DESCRIPTION
BOLMT Value
# Bits Used from LFSR Counter
2’b00
10
2’b01
8
2’b10
4
2’b11
1
相關PDF資料 |
PDF描述 |
|---|---|
| LAN9117-MD | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| LAN9117-MT | HIGH PERFORMANCE SINGLE-CHIP 10/100 NON-PCI ETHERNET CONTROLLER |
| LAN9118 | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MD | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
| LAN9118-MT | HIGH PERFORMANCE SINGLE CHIP 10/100NON PCI ETHERNET CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN9117-MD | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN9117-MT | 功能描述:以太網 IC HiPerfrm Sngl-Chip 10/100 Ethrnt RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN9118 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_05 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
| LAN9118_07 | 制造商:SMSC 制造商全稱:SMSC 功能描述:High Performance Single-Chip 10/100 Non-PCI Ethernet Controller |
發布緊急采購，3分鐘左右您將得到回復。