- 您現在的位置：買賣IC網 > PDF目錄358760 > LC72714 (Sanyo Electric Co.,Ltd.) Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder PDF資料下載
參數資料
| 型號： | LC72714 |
| 廠商： | Sanyo Electric Co.,Ltd. |
| 英文描述： | Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| 中文描述： | 多重移動調頻廣播集成電路片VICS解碼器 |
| 文件頁數： | 21/29頁 |
| 文件大?。?/td> | 232K |
| 代理商： | LC72714 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Control Program Compatibility
This IC allows the majority of the control software used to be compatible with Sanyo’s other FM multiplex ICs, in
particular, the LC72700E, LC72705E, LC72706E, LC72708E, and LC72709E(W). However, the following aspects of
the control software require modification.
Values of the register addresses
The addresses of the allowable BIC error count, synchronization error protection count, control registers, the layer 4
CRC register, and other registers have been modified.
The CCB address for serial I/O over a CCB bus has not been changed.
INT signal output timing
The INT signal output timing for data output is as follows. A circle ("O") indicates that INT is output, and a cross ("X")
indicates that the signal is not output.
Notes on Output Data Selection after Tuning (Reference)
When building an FM multiplex reception system, a tuning system is an absolute necessity. However, if it is
unacceptable for the IC to output data from the old station after tuning to a new station, the application must perform the
following processing.
(1) At the same time as tuning a new station, the application must set bit 4 (SYNC_RST) in control register 1 to set the
synchronization circuit to the unsynchronized state.
(2) Under the default settings, after the synchronization reset applications must acquire data according to the issued INT
signal.
The post-vertical correction output is not provided by the IC until frame synchronization has been established for the
new station after tuning and the first vertical correction operation has been performed.
(3) If bit 2 (VEC_OUT) in control register 2 has been enabled, applications must not use the post-vertical correction
output (data for which bit 7 in the status register is high) until frame synchronization has been reestablished.
This IC performs the portion of the DARC FM multiplex processing through layer 2 error correction without requiring
any special control operations. The IC itself cannot determine if the contents of the received data have changed or if a
new station has been tuned. This means that applications must use the procedure described above for this IC not to output
old data and only output the new data. Another point is that in IC synchronization, although it is rare for the old station
and the new station to be frame synchronized, applications need to perform the processing in item 1 above to cancel
frame synchronization forward protection period.
Notes:1. Data for which horizontal correction failed, but for which vertical correction succeeded is output.
2. All data is output.
3. If there is data for which horizontal correction failed, the post-vertical correction data for that data is output, regardless of whether or not vertical
correction succeeded.
(If the IC performs vertical correction, post-vertical correction data will be output.)
No. 6871-21/29
LC72714W
Control
register 1
bit 5,
INT_MOVE
Control
register 2
bit 2,
VEC_OUT
Horizontal correction output
Vertical correction output
Item
Operational overview
Correct
data
Incorrect
data
Parity
Correct
data
NG
Default value
L
L
Operation identical to that of the LC72705/06E and
LC72708/09E(W)
G
G
×
×
G
G
*
1
×
Combination 1
H
H
Operation identical to that of the LC72700E
All data is output
G
G
G
G
G
G
G
G
*
2
G
G
The output data selection conditions are cleared,
but there is no vertical correction output when
vertical correction is not performed
Combination 2
H
L
G
G
G
G
G
G
G
G
*
3
G
G
Combination 3
L
H
The output data selection conditions are retained,
but all of the vertical correction output is output
G
G
×
×
G
G
G
G
相關PDF資料 |
PDF描述 |
|---|---|
| LC72714W | Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72720NM | Single-Chip RDS Signal-Processing System LSI(單片無線電數據系統信號處理LSI（大規模集成電路）) |
| LC72720YV | Single-Chip RDS Signal-Processing System IC(單片無線電數據系統信號處理芯片) |
| LC72720 | Single-Chip RDS Signal-Processing System LSI |
| LC72720M | Single-Chip RDS Signal-Processing System LSI |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LC72714W | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72715PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:CMOS IC Mobile FM Multiplex Broadcast IC with On-Chip VICS Decoder |
| LC72717PW | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Mobile FM Multiplex Broadcast (DARC) Receiver IC |
| LC72720 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
| LC72720M | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:Single-Chip RDS Signal-Processing System LSI |
發布緊急采購，3分鐘左右您將得到回復。