參數資料
型號: LPC2387FBD100
廠商: NXP Semiconductors N.V.
元件分類: 數學處理器
英文描述: Single-chip 16-bit-32-bit MCU; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
封裝: LPC2387FBD100<SOT407-1 (LQFP100)|<<http://www.nxp.com/packages/SOT407-1.html<1<Always Pb-free,;
文件頁數: 56/64頁
文件大?。?/td> 447K
代理商: LPC2387FBD100
LPC2387
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2011. All rights reserved.
Product data sheet
Rev. 4 — 10 February 2011
56 of 64
NXP Semiconductors
LPC2387
Single-chip 16-bit/32-bit MCU
that belong to a specific C
L
. The value of external capacitances C
X1
and C
X2
specified in
this table are calculated from the internal parasitic capacitances and the C
L
. Parasitics
from PCB and package are not taken into account.
Table 16.
Crystal load capacitance
C
L
11 pF
13 pF
15 pF
14.4 XTAL and RTCX Printed Circuit Board (PCB) layout guidelines
The crystal should be connected on the PCB as close as possible to the oscillator input
and output pins of the chip. Take care that the load capacitors C
x1
, C
x2
, and C
x3
in case of
third overtone crystal usage have a common ground plane. The external components
must also be connected to the ground plain. Loops must be made as small as possible in
order to keep the noise coupled in via the PCB as small as possible. Also parasitics
should stay as small as possible. Values of C
x1
and C
x2
should be chosen smaller
accordingly to the increase in parasitics of the PCB layout.
14.5 Standard I/O pin configuration
Figure 25
shows the possible pin modes for standard I/O pins with analog input function:
Digital output driver: Open-drain mode enabled/disabled
Digital input: Pull-up enabled/disabled
Digital input: Pull-down enabled/disabled
Digital input: Repeater mode enabled/disabled
Analog input
The default configuration for standard I/O pins is input with pull-up enabled. The weak
MOS devices provide a drive capability equivalent to pull-up and pull-down resistors.
Recommended values for the RTC external 32 kHz oscillator C
X1
/C
X2
components
Maximum crystal series
resistance R
S
< 100 k
Ω
< 100 k
Ω
< 100 k
Ω
External load capacitors C
X1
/C
X2
18 pF, 18 pF
22 pF, 22 pF
27 pF, 27 pF
相關PDF資料
PDF描述
LPC2388FBD144 Single-chip 16-bit-32-bit micro; 512 kB flash with ISP-IAP, Ethernet, USB 2.0 device-host-OTG, CAN, and 10-bit ADC-DAC
LPC2420FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2420FET208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2460FBD208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
LPC2460FET208 Flashless 16-bit-32-bit microcontroller; Ethernet, CAN, ISP-IAP, USB 2.0 device-host-OTG, external memory interface
相關代理商/技術參數
參數描述
LPC2387FBD100,551 功能描述:ARM微控制器 - MCU 16/32 bit micro RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
LPC2387FBD100551 制造商:NXP Semiconductors 功能描述:IC 32BIT MCU 72MHZ LQFP-100
LPC2388 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit micro; 512 kB flash with ISP/IAP, Ethernet, USB 2.0 device/host/OTG, CAN, and 10-bit ADC/DAC
LPC2388FBD144 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Single-chip 16-bit/32-bit microcontroller; 512 kB flash with ISP/IAP, Ethernet, USB 2.0 device/host/OTG, CAN, and 10-bit ADC/DAC
LPC2388FBD144,551 功能描述:ARM微控制器 - MCU 16/32 bit micro RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT