參數資料
型號： LTC2410CGN
廠商： LINEAR TECHNOLOGY CORP
元件分類： ADC
英文描述： 20-Bit Universal Bus Driver With 3-State Outputs 56-SSOP -40 to 85
中文描述： 1-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO16
封裝： 0.150 INCH, PLASTIC, SSOP-16
文件頁數： 20/44頁
文件大?。?/td> 778K
代理商： LTC2410CGN
LTC2410
20
APPLICATIU
W
U
U
velocity is approximately 183ps/inch for internal traces
and 170ps/inch for surface traces. Thus, a driver gener-
ating a control signal with a minimum transition time of
1ns must be connected to the converter pin through a
trace shorter than 2.5 inches. This problem becomes
particularly difficult when shared control lines are used
and multiple reflections may occur. The solution is to
carefully terminate all transmission lines close to their
characteristic impedance.
Parallel termination near the LTC2410 pin will eliminate
this problem but will increase the driver power dissipation.
A series resistor between 27
and 56
placed near the
driver or near the LTC2410 pin will also eliminate this
problem without additional power dissipation. The actual
resistor value depends upon the trace impedance and
connection topology.
An alternate solution is to reduce the edge rate of the
control signals. It should be noted that using very slow
edges will increase the converter power supply current
during the transition time. The multiple ground pins used
in this package configuration, as well as the differential
input and reference architecture, reduce substantially the
converter’s sensitivity to ground currents.
Particular attention must be given to the connection of the
F
O
signal when the LTC2410 is used with an external
conversion clock. This clock is active during the conver-
sion time and the normal mode rejection provided by the
internal digital filter is not very high at this frequency. A
normal mode signal of this frequency at the converter
reference terminals may result into DC gain and INL
errors. A normal mode signal of this frequency at the
converter input terminals may result into a DC offset error.
Such perturbations may occur due to asymmetric capaci-
tive coupling between the F
O
signal trace and the converter
input and/or reference connection traces. An immediate
solution is to maintain maximum possible separation
between the F
O
signal trace and the input/reference sig-
nals. When the F
O
signal is parallel terminated near the
converter, substantial AC current is flowing in the loop
formed by the F
O
connection trace, the termination and the
ground return path. Thus, perturbation signals may be
inductively coupled into the converter input and/or refer-
ence. In this situation, the user must reduce to a minimum
the loop area for the F
O
signal as well as the loop area for
the differential input and reference connections.
Driving the Input and Reference
The input and reference pins of the LTC2410 converter are
directly connected to a network of sampling capacitors.
Depending upon the relation between the differential input
voltage and the differential reference voltage, these ca-
pacitors are switching between these four pins transfering
small amounts of charge in the process. A simplified
equivalent circuit is shown in Figure 15.
For a simple approximation, the source impedance R
S
driving an analog input pin (IN
+
, IN
–
, REF
+
or REF
–
) can be
considered to form, together with R
SW
and C
EQ
(see
Figure15), a first order passive network with a time
constant
τ
= (R
S
+ R
SW
) C
EQ
. The converter is able to
sample the input signal with better than 1ppm accuracy if
the sampling period is at least 14 times greater than the
input circuit time constant
τ
. The sampling process on the
four input analog pins is quasi-independent so each time
constant should be considered by itself and, under worst-
case circumstances, the errors may add.
When using the internal oscillator (F
O
= LOW or HIGH), the
LTC2410’s front-end switched-capacitor network is clocked
at 76800Hz corresponding to a 13
μ
s sampling period.
Thus, for settling errors of less than 1ppm, the driving
source impedance should be chosen such that
τ
≤
13
μ
s/14
= 920ns. When an external oscillator of frequency f
EOSC
is
used, the sampling period is 2/f
EOSC
and, for a settling
error of less than 1ppm,
τ
≤
0.14/f
EOSC
.
Input Current
If complete settling occurs on the input, conversion re-
sults will be unaffected by the dynamic input current. An
incomplete settling of the input signal sampling process
may result in gain and offset errors, but it will not degrade
the INL performance of the converter. Figure 15 shows the
mathematical expressions for the average bias currents
flowing through the IN
+
and IN
–
pins as a result of the
sampling charge transfers when integrated over a sub-
stantial time period (longer than 64 internal clock cycles).
相關PDF資料
PDF描述
LTC2410IGN 24-Bit No Latency ADC with Differential Input and Differential Reference
LTC2410 20-Bit Universal Bus Driver With 3-State Outputs 56-SSOP -40 to 85
LTC2410C 20-Bit Universal Bus Driver With 3-State Outputs 56-TVSOP -40 to 85
LTC2410I 20-Bit Universal Bus Driver With 3-State Outputs 56-SSOP -40 to 85
LTC2411 2.7V to 5.5V Micropower 24-Bit Differential Σ△ Analog to Digital Converter(2.7V ～5.5V，微功耗，24位差分Σ△串行模數轉換器)
相關代理商/技術參數
參數描述
LTC2410CGN#PBF 功能描述:IC ADC 24BIT DIFF INP/REF 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2410CGN#PBF 制造商:Linear Technology 功能描述:A/D Converter (A-D) IC
LTC2410CGN#TR 功能描述:IC ADC 24BIT DIFF INP/REF 16SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2410CGN#TRPBF 功能描述:IC ADC 24BIT DIFF INP/REF 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2410CGNPBF 制造商:Linear Technology 功能描述:ADC,LTC2410C 24bit diff D-S SPI SSOP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*