參數資料
型號: LTC2414CGN
廠商: LINEAR TECHNOLOGY CORP
元件分類: ADC
英文描述: 8-/16-Channel 24-Bit No Latency TM ADCs
中文描述: 8-CH 24-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO28
封裝: 0.150 INCH, PLASTIC, SSOP-28
文件頁數: 13/48頁
文件大?。?/td> 775K
代理商: LTC2414CGN
LTC2414/LTC2418
13
241418fa
specification for the REF
+
and REF
pins covers the entire
range from GND to V
CC
. For correct converter operation,
the REF
+
pin must always be more positive than the REF
pin.
The LTC2414/LTC2418 can accept a differential reference
voltage from 0.1V to V
CC
. The converter output noise is
determined by the thermal noise of the front-end circuits,
and, as such, its value in nanovolts is nearly constant with
reference voltage. A decrease in reference voltage will not
significantly improve the converter’s effective resolution.
On the other hand, a reduced reference voltage will im-
prove the converter’s overall INL performance. A reduced
reference voltage will also improve the converter perfor-
mance when operated with an external conversion clock
(external F
O
signal) at substantially higher output data rates.
Input Voltage Range
The two selected pins are labeled IN
+
and IN
(see Tables
1 and 2). Once selected (either differential or single-ended
multiplexing mode), the analog input is differential with a
common mode range for the IN
+
and IN
input pins ex-
tending from GND – 0.3V to V
CC
+ 0.3V. Outside
these limits, the ESD protection devices begin to turn on
and the errors due to input leakage current increase rap-
idly. Within these limits, the LTC2414/LTC2418 convert
the bipolar differential input signal, V
IN
= IN
+
– IN
, from
–FS = –0.5 V
REF
to +FS = 0.5 V
REF
where V
REF
=
REF
+
– REF
. Outside this range the converters indicate
the overrange or the underrange condition using distinct
output codes.
Input signals applied to IN
+
and IN
pins may extend
300mV below ground or above V
CC
. In order to limit any
fault current, resistors of up to 5k may be added in series
with the IN
+
or IN
pins without affecting the performance
of the device. In the physical layout, it is important to
maintain the parasitic capacitance of the connection be-
tween these series resistors and the corresponding pins
as low as possible; therefore, the resistors should be
located as close as practical to the pins. In addition, series
resistors will introduce a temperature dependent offset
error due to the input leakage current. A 1nA input leakage
current will develop a 1ppm offset error on a 5k resistor if
V
REF
= 5V. This error has a very strong temperature
dependency.
Input Data Format
When the LTC2414/LTC2418 are powered up, the default
selection used for the first conversion is IN
+
= CH0 and IN
= CH1 (Address = 00000). In the data input/output mode
following the first conversion, a channel selection can be
updated using an 8-bit word. The LTC2414/LTC2418
serial input data is clocked into the SDI pin on the rising
edge of SCK (see Figure 3). The input is composed of an
8-bit word with the first 3 bits acting as control bits and the
remaining 5 bits as the channel address bits.
The first 2 bits are always 10 for proper updating opera-
tion. The third bit is EN. For EN = 1, the following 5 bits are
used to update the input channel selection. For EN = 0,
previous channel selection is kept and the following bits
are ignored. Therefore, the address is updated when the 3
control bits are 101 and kept for 100. Alternatively, the 3
control bits can be all zero to keep the previous address.
This alternation is intended to simplify the SDI interface
allowing the user to simply connect SDI to ground if no
update is needed. Combinations other than 101, 100 and
000 of the 3 control bits should be avoided.
When update operation is set (101), the following 5 bits
are the channel address. The first bit, SGL, decides if the
differential selection mode (SGL = 0) or the single-ended
selection mode is used (SGL = 1). For SGL = 0, two
adjacent channels can be selected to form a differential
input; for SGL = 1, one of the 8 channels (CH0-CH7) for the
LTC2414 or one of the 16 channels (CH0-CH15) for the
LTC2418 is selected as the positive input and the COM pin
is used as the negative input. For the LTC2414, the lower
half channels (CH0-CH7) are used and the channel ad-
dress bit A2 should be always 0, see Table 1. While for the
LTC2418, all the 16 channels are used and the size of the
corresponding selection table (Table 2) is doubled from
that of the LTC2414 (Table 1). For a given channel selec-
tion, the converter will measure the voltage between the
two channels indicated by IN
+
and IN
in the selected row
of Tables 1 or 2.
APPLICATIOU
W
U
U
相關PDF資料
PDF描述
LTC2414IGN 8-/16-Channel 24-Bit No Latency TM ADCs
LTC2418CGN 8-/16-Channel 24-Bit No Latency TM ADCs
LTC2418IGN 8-/16-Channel 24-Bit No Latency TM ADCs
LTC2415-1CGN 24-Bit No Latency ADCs with Differential Input and Differential Reference
LTC2415-1IGN 24-Bit No Latency ADCs with Differential Input and Differential Reference
相關代理商/技術參數
參數描述
LTC2414CGN#PBF 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2414CGN#PBF 制造商:Linear Technology 功能描述:IC ADC 24BIT SSOP-28
LTC2414CGN#TR 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2414CGN#TRPBF 功能描述:IC ADC 8CH 24BIT DIFFINPUT28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2414CGNPBF 制造商:Linear Technology 功能描述:ADC,LTC2414C 24bit D-S 8 ch SPI SSOP