- 您現在的位置：買賣IC網 > PDF目錄377770 > LTC2439-1 (Linear Technology Corporation) 8-/16-Channel 16-Bit No Latency Delta-Sigma ADC PDF資料下載
參數資料
| 型號： | LTC2439-1 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | ADC |
| 英文描述： | 8-/16-Channel 16-Bit No Latency Delta-Sigma ADC |
| 中文描述： | 8-/16-Channel 16位無延遲增量累加模數轉換器 |
| 文件頁數： | 14/28頁 |
| 文件大?。?/td> | 288K |
| 代理商： | LTC2439-1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2439-1
14
24391f
Finally, CS can be used to control the free-running mode
of operation, see Serial Interface Timing Modes section.
Grounding CS will force the ADC to continuously convert
at the maximum output rate selected by F
O
.
SERIAL INTERFACE TIMING MODES
The LTC2439-1’s 4-wire interface is SPI and MICROWIRE
compatible. This interface offers several flexible modes of
operation. These include internal/external serial clock,
3- or 4-wire I/O, single cycle conversion. The following
sections describe each of these serial interface timing
modes in detail. In all these cases, the converter can use
the internal oscillator (F
O
= LOW) or an external oscillator
connected to the F
O
pin. Refer to Table6 for a summary.
External Serial Clock, Single Cycle Operation
(SPI/MICROWIRE Compatible)
This timing mode uses an external serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 6.
The serial clock mode is selected on the falling edge of CS.
To select the external serial clock mode, the serial clock pin
(SCK) must be LOW during each CS falling edge.
The serial data output pin (SDO) is Hi-Z as long as CS is
HIGH. At any time during the conversion cycle, CS may be
pulled LOW in order to monitor the state of the converter.
While CS is pulled LOW, EOC is output to the SDO pin.
EOC=1 while a conversion is in progress and EOC = 0 if
the conversion is complete. If CS is HIGH, the device
automatically enters the low power sleep state once the
conversion is complete.
When the device is in the sleep state, its conversion result
is held in an internal static shift register. The device
remains in the sleep state until the first rising edge of SCK
Table 6. LTC2439-1 Interface Timing Modes
Conversion
Cycle
Control
CS and SCK
SCK
CS
↓
Continuous
Data
Output
Control
CS and SCK
SCK
CS
↓
Internal
Connection
and
Waveforms
Figures 6, 7
Figure 8
Figures 9, 10
Figure 11
SCK
Source
External
External
Internal
Internal
Configuration
External SCK, Single Cycle Conversion
External SCK, 3-Wire I/O
Internal SCK, Single Cycle Conversion
Internal SCK, 3-Wire I/O, Continuous Conversion
When CS (Pin 16) is HIGH or the converter is in the con-
version state, the SDI input is ignored and may be driven
HIGH or LOW. When CS goes LOW and the conversion is
complete, SDO goes low and then SDI starts to shift in bits
on the rising edge of SCK.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 17), provides the
result of the last conversion as a serial bit stream (MSB
first) during the data output state. In addition, the SDO pin
is used as an end of conversion indicator during the
conversion and sleep states.
When CS (Pin 16) is HIGH, the SDO driver is switched to
a high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW. The device remains in the sleep state until the first
rising edge of SCK occurs while CS = LOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 16), is used to test the
conversion status and to enable the data input/output
transfer as described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2439-1 will abort any serial data
transfer in progress and start a new conversion cycle
anytime a LOW-to-HIGH transition is detected at the CS
pin after the converter has entered the data input/output
state (i.e., after the first rising edge of SCK occurs with
CS=LOW). If the device has not finished loading the last
input bit (A0 of SDI) by the time CS pulled HIGH, the
address information is discarded and the previous ad-
dress is kept.
APPLICATIOU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2439-1IGN | 8-/16-Channel 16-Bit No Latency Delta-Sigma ADC |
| LTC2440CGN | 24-Bit High Speed Differential delta-sigma ADC with Selectable Speed/Resolution |
| LTC2440IGN | 24-Bit High Speed Differential delta-sigma ADC with Selectable Speed/Resolution |
| LTC2444 | 24-Bit High Speed 8-/16-Channel ADCs with Selectable Speed/Resolution |
| LTC2444C | 24-Bit High Speed 8-/16-Channel ADCs with Selectable Speed/Resolution |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2439-1CGN | 功能描述:IC ADC 16BIT 16CH MCRPWR 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2439-1CGN#PBF | 功能描述:IC ADC 16BIT 16CH MCRPWR 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2439-1CGN#TR | 功能描述:IC ADC 16BIT 16CH MCRPWR 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2439-1CGN#TRPBF | 功能描述:IC ADC 16BIT 16CH MCRPWR 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC24391IGN | 制造商:Linear Technology 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。
