參數資料
型號： M25PE16-VMW6TP
廠商： 意法半導體
元件分類： DRAM
英文描述： 4 Mbit Uniform Sector, Serial Flash Memory
中文描述： 4兆位統一部門，串行閃存
文件頁數： 41/56頁
文件大小： 334K
代理商： M25PE16-VMW6TP
M25PE16
Instructions
41/56
6.16
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction is the only way to put the device in the
lowest consumption mode (the Deep Power-down mode). It can also be used as an extra
software protection mechanism, while the device is not in active use, since in this mode, the
device ignores all Write, Program and Erase instructions.
Driving Chip Select (S) High deselects the device, and puts the device in the Standby mode
(if there is no internal cycle currently in progress). But this mode is not the Deep Power-
down mode. The Deep Power-down mode can only be entered by executing the Deep
Power-down (DP) instruction, subsequently reducing the standby current (from I
CC1
to I
CC2
,
as specified in
Table 17
).
Once the device has entered the Deep Power-down mode, all instructions are ignored
except the Release from Deep Power-down (RDP) instruction. Issuing the Release from
Deep Power-down (RDP) instruction will cause the device to exit the Deep Power-down
mode.
The Deep Power-down mode automatically stops at Power-down, and the device always
Powers-up in the Standby mode.
The Deep Power-down (DP) instruction is entered by driving Chip Select (S) Low, followed
by the instruction code on Serial Data Input (D). Chip Select (S) must be driven Low for the
entire duration of the sequence.
The instruction sequence is shown in
Figure 21
.
Chip Select (S) must be driven High after the eighth bit of the instruction code has been
latched in, otherwise the Deep Power-down (DP) instruction is not executed. As soon as
Chip Select (S) is driven High, it requires a delay of t
DP
before the supply current is reduced
to I
CC2
and the Deep Power-down mode is entered.
Any Deep Power-down (DP) instruction, while an Erase, Program or Write cycle is in
progress, is rejected without having any effects on the cycle that is in progress.
Figure 21.
Deep Power-down (DP) instruction sequence
C
D
AI03753D
S
2
1
3
4
5
6
7
0
t
DP
Deep Power-down Mode
Stand-by Mode
Instruction
相關PDF資料
PDF描述
M25PE40 4 Mbit Uniform Sector, Serial Flash Memory
M25PE40VMN6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE40VMN6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE40VMN6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25PE40VMN6TP 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25PE20 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout
M25PE20_07 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 and 2 Mbit, low voltage, Page-Erasable Serial Flash memories with Byte-Alterability, 50 MHz SPI bus, standard pinout
M25PE20-V6D11 制造商:Micron Technology Inc 功能描述:SERIAL NOR 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Gel-pak, waffle pack, wafer, diced wafer on film
M25PE20-VMN6G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:1 and 2 Mbit, low voltage, Page-Erasable Serial Flash memories with Byte-Alterability, 50 MHz SPI bus, standard pinout
M25PE20-VMN6P 功能描述:閃存 1 AND 2 MBIT LV SERIAL FL RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*