- 您現在的位置：買賣IC網 > PDF目錄358974 > M25PE80-VMW6TP (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25PE80-VMW6TP |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 28/43頁 |
| 文件大?。?/td> | 599K |
| 代理商： | M25PE80-VMW6TP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
M25PE80
28/43
Deep Power-down (DP)
Executing the Deep Power-down (DP) instruction
is the only way to put the device in the lowest con-
sumption mode (the Deep Power-down mode). It
can also be used as an extra software protection
mechanism, while the device is not in active use,
since in this mode, the device ignores all Write,
Program and Erase instructions.
Driving Chip Select (S) High deselects the device,
and puts the device in the Standby mode (if there
is no internal cycle currently in progress). But this
mode is not the Deep Power-down mode. The
Deep Power-down mode can only be entered by
executing the Deep Power-down (DP) instruction,
subsequently reducing the standby current (from
I
CC1
to I
CC2
, as specified in
Table 15.
).
Once the device has entered the Deep Power-
down mode, all instructions are ignored except the
Release from Deep Power-down (RDP) instruc-
tion. Issuing the Release from Deep Power-down
(RDP) instruction will cause the device to exit the
Deep Power-down mode.
The Deep Power-down mode automatically stops
at Power-down, and the device always Powers-up
in the Standby mode.
The Deep Power-down (DP) instruction is entered
by driving Chip Select (S) Low, followed by the in-
struction code on Serial Data Input (D). Chip Se-
lect (S) must be driven Low for the entire duration
of the sequence.
The instruction sequence is shown in
Figure 21.
.
Chip Select (S) must be driven High after the
eighth bit of the instruction code has been latched
in, otherwise the Deep Power-down (DP) instruc-
tion is not executed. As soon as Chip Select (S) is
driven High, it requires a delay of t
DP
before the
supply current is reduced to I
CC2
and the Deep
Power-down mode is entered.
Any Deep Power-down (DP) instruction, while an
Erase, Program or Write cycle is in progress, is re-
jected without having any effects on the cycle that
is in progress.
Figure 21. Deep Power-down (DP) Instruction Sequence
C
D
AI03753D
S
2
1
3
4
5
6
7
0
t
DP
Deep Power-down Mode
Stand-by Mode
Instruction
相關PDF資料 |
PDF描述 |
|---|---|
| M25PE80-VMW6T | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMW6P | COIL CHOKE 27MH .50A RADIAL |
| M25PE80-VMW6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMW6 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PXX | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25PF32-VMW6G | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Trays |
| M25PF32-VMW6TG | 制造商:Micron Technology Inc 功能描述:SERIAL NOR - Tape and Reel |
| M25PG11-0M | 制造商:Jacob 功能描述: |
| M25PG13-0M | 制造商:Jacob 功能描述: |
| M25-PG21 | 制造商:Mencom 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。