- 您現在的位置：買賣IC網 > PDF目錄359053 > M29W800AB100ZA5T (意法半導體) 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory PDF資料下載
參數資料
| 型號： | M29W800AB100ZA5T |
| 廠商： | 意法半導體 |
| 英文描述： | 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory |
| 中文描述： | 8兆1兆x8或512KB的x16插槽，引導塊低壓單電源閃存 |
| 文件頁數： | 4/33頁 |
| 文件大?。?/td> | 234K |
| 代理商： | M29W800AB100ZA5T |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
M29W800AT, M29W800AB
4/33
Bus Operations
The following operations can be performed using
the appropriate buscycles: Read (Array, Electron-
ic Signature, Block Protection Status), Write com-
mand, Output Disable, Stan-by, Reset, Block
Protection, Unprotection, Protection Verify, Unpro-
tection Verify and Block Temporary Unprotection.
See Tables 5 and 6.
Command Interface
Instructions, made up of commands written in cy-
cles, can be given to the Program/Erase Controller
through a Command Interface (C.I.). For added
data protection, program or erase execution starts
after 4 or 6 cycles. The first, second, fourth and
fifth cycles are used to input Coded cycles to the
C.I. This Coded sequence is the same for all Pro-
gram/Erase Controller instructions. The ’Com-
mand’ itself and its confirmation, when applicable,
are given on the third, fourth or sixth cycles. Any
incorrect commandor any improper command se-
quence will reset the device to Read Array mode.
Instructions
Seven instructions are defined to perform Read
Array, Auto Select (to read the Electronic Signa-
ture or Block Protection Status), Program, Block
Erase, Chip Erase, Erase Suspend and Erase Re-
sume.
The internal P/E.C. automatically handles all tim-
ing and verification of the Program and Erase op-
erations. The
Status Register Data
Toggle, Error bits and the RB output may be read
at any time, during programming or erase, to mon-
itor the progress of the operation.
Instructions are composed of up to six cycles. The
first two cycles input a Coded sequence to the
Command Interface which is common to all in-
structions (see Table 9).
The third cycle inputs the instruction set-up com-
mand. Subsequent cycles output the addressed
data, Electronic Signature or Block Protection Sta-
tus for Read operations. Inorder to give additional
data protection, the instructions for Program and
Block or Chip Erase require further command in-
puts. For a Program instruction, the fourth com-
mand cycle inputs the address and data to be
programmed. For an Erase instruction (Block or
Chip), the fourth and fifth cycles input a further
Coded sequence before the Erase confirm com-
mand on the sixth cycle. Erasure of a memory
block may be suspended, in order to read data
from another block or to program data in another
block, and then resumed. When power is first ap-
plied or if V
CC
falls below V
LKO
, the command in-
terface is reset to Read Array.
Polling,
Table 2. Absolute Maximum Ratings
(1)
Note: 1. Except for the rating ”O(jiān)perating Temperature Range”, stresses above those listed in the Table ”Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions
above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi-
tions forextended periods may affect device reliability. Referalso to theSTMicroelectronics SURE Program and other relevantqual-
ity documents.
2. Minimum Voltage may undershoot to –2V during transition and for less than 20ns during transitions.
3. Depends on range.
Symbol
Parameter
Value
Unit
T
A
Ambient Operating Temperature
(3)
–40 to 85
°
C
T
BIAS
Temperature Under Bias
–50 to 125
°
C
T
STG
Storage Temperature
–65 to 150
°
C
V
IO(2)
Input or Output Voltage
–0.6 to 5
V
V
CC
Supply Voltage
–0.6 to 5
V
V
(A9, E, G, RP)(2)
A9, E, G, RP Voltage
–0.6 to 13.5
V
相關PDF資料 |
PDF描述 |
|---|---|
| M29W800AT100ZA5T | 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory |
| M29W800AB90ZA5T | 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory |
| M29W800AT90ZA5T | 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory |
| M29W800AB80ZA5T | 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory |
| M29W800AT80ZA5T | 8 Mbit 1Mb x8 or 512Kb x16, Boot Block Low Voltage Single Supply Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M29W800AB120M1 | 功能描述:閃存 1Mx8 or 512Kx16 120n RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M29W800AB120N1 | 功能描述:閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M29W800AB-120N1 | 制造商:STMicroelectronics 功能描述: |
| M29W800AB120N6 | 制造商:Micron Technology Inc 功能描述:FLASH PARALLEL 3V/3.3V 8MBIT 1MX8/512KX16 120NS 48TSOP - Trays |
| M29W800AB120ZA6 | 功能描述:閃存 LFBGA48 1MX8 512KX16 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。