- 您現在的位置：買賣IC網 > PDF目錄45029 > M37161MF-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 PDF資料下載
參數資料
| 型號： | M37161MF-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| 封裝： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件頁數： | 39/129頁 |
| 文件大?。?/td> | 1092K |
| 代理商： | M37161MF-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁
Rev.1.00
2003.11.25
page 17 of 128
M37161M8/MA/MF-XXXSP/FP,M37161EFSP/FP
Priority
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
8.3 INTERRUPTS
Interrupts can be caused by 16 different sources comprising 4 exter-
nal, 10 internal, 1 software, and reset. Interrupts are vectored inter-
rupts with priorities as shown in Table 8.3.1. Reset is also included in
the table because its operation is similar to an interrupt.
When an interrupt is accepted,
The contents of the program counter and processor status regis-
ter are automatically stored into the stack.
The interrupt disable flag I is set to “1” and the corresponding
interrupt request bit is set to “0.”
The jump destination address stored in the vector address enters
the program counter.
Other interrupts are disabled when the interrupt disable flag is set to
“1.”
All interrupts except the BRK instruction interrupt have an interrupt
request bit and an interrupt enable bit. The interrupt request bits are
in interrupt request registers 1 and 2 and the interrupt enable bits are
in interrupt control registers 1 and 2. Figures 8.3.2 to 8.3.6 show the
interrupt-related registers.
Interrupts other than the BRK instruction interrupt and reset are ac-
cepted when the interrupt enable bit is “1,” interrupt request bit is “1,”
and the interrupt disable flag is “0.” The interrupt request bit can be
set to “0” by a program, but not set to “1.” The interrupt enable bit can
be set to “0” and “1” by a program.
Reset is treated as a non-maskable interrupt with the highest priority.
Figure 8.3.1 shows interrupt control.
8.3.1 Interrupt Sources
(1) VSYNC, OSD interrupts
The VSYNC interrupt is an interrupt request synchronized with
the vertical sync signal.
The OSD interrupt occurs after character block display to the
CRT is completed.
(2) INT1 to INT3 external interrupts
The INT1 to INT3 interrupts are external interrupt inputs, the sys-
tem detects that the level of a pin changes from LOW to HIGH or
from HIGH to LOW, and generates an interrupt request. The in-
put active edge can be selected by bits 3 to 5 of the interrupt
input polarity register (address 00DC16) : when this bit is “0,” a
change from LOW to HIGH is detected; when it is “1,” a change
from HIGH to LOW is detected. Note that both bits are cleared to
“0” at reset.
(3) Timers 1 to 4 interrupts
An interrupt is generated by an overflow of timers 1 to 4.
Vector Addresses
FFFF16, FFFE16
FFFD16, FFFC16
FFFB16, FFFA16
FFF716, FFF616
FFF516, FFF416
FFF316, FFF216
FFF116, FFF016
FFEF16, FFEE16
FFED16, FFEC16
FFEB16, FFEA16
FFE916, FFE816
FFE716, FFE616
FFE516, FFE416
FFE316, FFE216
FFDF16, FFDE16
Interrupt Source
Reset
OSD interrupt
INT1 external interrupt
Serial I/O interrupt
Timer 4 interrupt
f(XIN)/4096 interrupt
VSYNC interrupt
Timer 3 interrupt
Timer 2 interrupt
Timer 1 interrupt
INT3 external interrupt
INT2 external interrupt
Multi-master I2C-BUS interface interrupt
Timer 5 6 interrupt
BRK instruction interrupt
Remarks
Non-maskable
Active edge selectable
Source switch by software (see note)
Non-maskable
Table 8.3.1 Interrupt Vector Addresses and Priority
Note: Switching a source during a program causes an unnecessary interrupt. Therefore, set a source at initializing of program.
相關PDF資料 |
PDF描述 |
|---|---|
| M37161EFSP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37161MA-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37161M8-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42 |
| M37202E3SP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP64 |
| M37207EFFP | 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3720 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 KEY 1 SOUND |
| M3720-1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 KEY 1 SOUND |
| M3720-10 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 KEY 1 SOUND |
| M3720-2 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 KEY 1 SOUND |
| M3720-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 KEY 1 SOUND |
發布緊急采購，3分鐘左右您將得到回復。