參數資料
型號： M37905M4C-XXXFP
元件分類： 微控制器/微處理器
英文描述： 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
封裝： 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64
文件頁數： 32/102頁
文件大?。?/td> 881K
代理商： M37905M4C-XXXFP
35
M37905M4C-XXXFP, M37905M4C-XXXSP
M37905M6C-XXXFP, M37905M6C-XXXSP
M37905M8C-XXXFP, M37905M8C-XXXSP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
TIMER B
Figure 35 shows a block diagram of timer B.
Timer B has three modes: timer mode, event counter mode, and
pulse period measurement/pulse width measurement mode. The
mode is selected with bits 0 and 1 of the timer Bi mode register (i=0
to 2). Each of these modes is described below.
(1) Timer mode [00]
Figure 36 shows the bit configuration of the timer Bi mode register in
the timer mode. Bits 0 and 1 of the timer Bi mode register must al-
ways be “0” in timer mode.
Bits 6 and 7 are used to select the clock source. The counting of the
selected clock starts when the count start bit is “1” and stops when
“0”.
As shown in Figure 21, the timer Bi’s count start bits are allocated at
the same address to which some of the timer Ai’s count start bits are
allocated. (In other words, they are allocated in the count start regis-
ter 0.) The count is decremented, an interrupt occurs, and the inter-
rupt request bit in the timer Bi interrupt control register is set when
the contents becomes 000016. At the same time, the contents of the
reload register is stored in the counter and count is continued.
Timer Bi does not have a pulse output function or a gate function like
timer A.
When data is written to timer Bi halted, it is written to the reload reg-
ister and the counter. When data is written to timer Bi which is busy,
the data is written to the reload register, but not to the counter. The
new data is reloaded from the reload register to the counter at the
next reload time and counting continues.
The contents of the counter can be read at any time.
Fig. 35 Block diagram of timer B
Data bus (odd)
Data bus (even)
Reload register (16)
Counter (16)
Count start register 0
Event counter
mode
Notes 1: Perform a write and read to/from timer Bi register in the condition of 16-bit data length : data length flag (m) = “0”.
2: Only for timer B2, a count source in the event counter mode can be selected.
(Address 4016)
Counter reset
circuit
Timer mode
Pulse period measurement/Pulse
width measurement mode
(Low-order 8 bits)
(High-order 8 bits)
f2
f16
f64
f512
Count source select bits
fx32
Polarity selection
and edge pulse
generator
TBiIN
Timer B2 clock source
select bit (Note 2)
Timer B2 clock source select bit : Bit 6 at address 6316
Addresses
Timer B0 5116 5016
Timer B1 5316 5216
Timer B2 5516 5416
相關PDF資料
PDF描述
M37905M8C-XXXFP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
M37905M8C-XXXSP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP64
M37905M4C-XXXSP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP64
M37905M4C-XXXFP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
M37905M8C-XXXFP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M37905M4C-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37905M6C-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37905M6C-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37905M8C-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
M37905M8C-XXXSP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16 BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*