- 您現在的位置：買賣IC網 > PDF目錄45047 > M38588GCFP 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 PDF資料下載
參數資料
| 型號： | M38588GCFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 6.25 MHz, MICROCONTROLLER, PDSO42 |
| 封裝： | 8.40 X 17.50 MM, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件頁數： | 69/77頁 |
| 文件大?。?/td> | 824K |
| 代理商： | M38588GCFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁
Rev.1.10
Apr 3, 2006
page 71 of 75
REJ03B0139-0110
3858 Group
NOTES ON PERIPHERAL FUNCTIONS
Notes on Input and Output Ports
1. Notes in standby state
In standby state*1 , do not make input levels of an I/O port “unde-
fined”, especially for I/O ports of the N-channel open-drain. When
setting the N-channel open-drain port as an output, do not make
input levels of an I/O port “undefined”, too.
Pull-up (connect the port to VCC) or pull-down (connect the port to
VSS) these ports through a resistor.
When determining a resistance value, note the following points:
External circuit
Variation of output levels during the ordinary operation
<Reason>
When setting as an input port with its direction register, the tran-
sistor becomes the OFF state, which causes the ports to be the
high-impedance state.
Accordingly, the potential which is input to the input buffer in a mi-
crocomputer is unstable in the state that input levels of an I/O port
are “undefined”. This may cause power source current.
In I/O ports of N-channel open-drain, when the contents of the port
latch are “1”, even if it is set as an output port with its direction
register, it becomes the same phenomenon as the case of an in-
put port.
*1 Standby state : stop mode by executing STP instruction
wait mode by executing WIT instruction
2. Modifying output data with bit managing
instruction
When the port latch of an I/O port is modified with the bit manag-
ing instruction*2 , the value of the unspecified bit may be changed.
<Reason>
The bit managing instructions are read-modify-write form instruc-
tions for reading and writing data by a byte unit.
Accordingly, when these instructions are executed on a bit of the
port latch of an I/O port, the following is executed to all bits of the
port latch.
As for bit which is set for input port:
The pin state is read in the CPU, and is written to this bit after bit
managing.
As for bit which is set for output port:
The bit value is read in the CPU, and is written to this bit after bit
managing.
Note the following:
Even when a port which is set as an output port is changed for
an input port, its port latch holds the output data.
As for a bit of which is set for an input port, its value may be
changed even when not specified with a bit managing instruction
in case where the pin state differs from its port latch contents.
*2 Bit managing instructions : SEB and CLB instructions
Termination of Unused Pins
1. Terminate unused pins
(1) I/O ports :
Set the I/O ports for the input mode and connect them to VCC or
VSS through each resistor of 1 k
to 10 k. In the port which can
select a internal pull-up resistor, the internal pull-up resistor can
be used.
Set the I/O ports for the output mode and open them at “L” or
“H”.
When opening them in the output mode, the input mode of the
initial status remains until the mode of the ports is switched over
to the output mode by the program after reset. Thus, the poten-
tial at these pins is undefined and the power source current may
increase in the input mode. With regard to an effects on the sys-
tem, thoroughly perform system evaluation on the user side.
Since the direction register setup may be changed because of a
program runaway or noise, set direction registers by program pe-
riodically to increase the reliability of program.
(2) The AVSS pin when not using the A/D converter :
When not using the A/D converter, handle a power source pin for
the A/D converter, AVSS pin as follows:
AVSS: Connect to the VSS pin.
2. Termination remarks
(1) Input ports and I/O ports :
Do not open in the input mode.
<Reason>
The power source current may increase depending on the
firststage circuit.
An effect due to noise may be easily produced as compared with
proper termination (1) in 1 shown on the above.
(2) I/O ports :
When setting for the input mode, do not connect to VCC or VSS di-
rectly.
<Reason>
If the direction register setup changes for the output mode be-
cause of a program runaway or noise, a short circuit may occur
between a port and VCC (or VSS).
(3) I/O ports :
When setting for the input mode, do not connect multiple ports in
a lump to VCC or VSS through a resistor.
<Reason>
If the direction register setup changes for the output mode be-
cause of a program runaway or noise, a short circuit may occur
between ports.
At the termination of unused pins, perform wiring at the shortest
possible distance (20 mm or less) from microcomputer pins.
相關PDF資料 |
PDF描述 |
|---|---|
| M38749EFT | 8-BIT, OTPROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747M4T | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747M6T | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747M8T | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
| M38747MCF | 8-BIT, MROM, 6.4 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38588GCFP#U0 | 功能描述:IC 740/3858 MCU QZ-ROM 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M38588GCSP#U0 | 功能描述:IC 740/3858 MCU QZ-ROM 42DIP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M3860 | 功能描述:電纜固定件和配件 FLEX LTSCG 500 RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
| M3860 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 14AWG BLK 1000' |
| M3860 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 14AWG BLK 500' |
發布緊急采購，3分鐘左右您將得到回復。