參數資料
型號: M38D24G4HP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
封裝: 10X 10 MM, 0.50 MM PITCH, PLASTIC, LQFP-64
文件頁數: 113/138頁
文件大?。?/td> 2880K
代理商: M38D24G4HP
Rev.3.02
Apr 10, 2008
Page 74 of 131
REJ03B0177-0302
38D2 Group
Fig 73. Structure of flash memory control register 2
Figure 74 shows a flowchart for setting/releasing CPU rewrite mode.
Fig 74. CPU rewrite mode set/release flowchart be sure to execute
Flash memory control register 2
(FM CR2: address : 0FE216, initial value: 4516)
Not used (return “1” when read)
Not used (do not write “1” to this bit.)
Not used (return “1” when read)
Not used (return “0” when read)
User block 0 E/W enable bit (1, 2)
0 : E/W disabled (800016-FFFF16)
1 : E/W enabled (800016-FFFF16)
Not used (return “0” when read)
Not used (return “1” when read)
Not used (return “0” when read)
b7
b0
Notes 1: For this bit to be set to “1”, the user needs to write a “0” and then a
“1” to it in succession. For this bit to be set to “0”, write “0” only to this
bit.
2: Effective only when the CPU rewrite m ode select bit = “1”.
Table 16 State of E/W inhibition function
User block 0
E/W enable bit
User block 1
E/W enable bit
User block 0
Addresses 800016 to FFFF16
User block 1
Addresses 180016 to 7FFF16
Data block
Addresses 100016 to 17FF16
0
E/W disabled
E/W enabled
0
1
E/W disabled
E/W enabled
1
0
E/W enabled
E/W disabled
E/W enabled
1
E/W enabled
Start
Single-chip mode or Boot mode
Set CPU mode register(1)
Jump to control program transferred to internal RAM
(Subsequent operations are executed by control program in
this RAM)
Transfer CPU rewrite mode control program to internal RAM
Set CPU rewrite mode select bit to “1” (by writing “0” and
then “1” in succession)
Using software command executes erase, program, or other
operation
End
Write “0” to CPU rewrite mode select bit
Set user block 0 E/W enable bit to “1” (by writing “0” and
then “1” in succession)
Set user block 1 E/W enable bit (At E/W disabled; writing
“0” , at E/W enabled;
writing “0” and then “1” in succession
Execute read array command(2)
Set user block 0 E/W enable bit to “0”
Set user block 1 E/W enable bit to “0”
Notes 1: Set the main clock as follows depending on the clock division ratio selection bits of CPU mode register (bits 6, 7 of address 003B16).
2: Before exiting the CPU rewrite mode after completing erase or program operation, always be sure to execute the read array command.
相關PDF資料
PDF描述
M38D29GC-XXXHP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D24G4-XXXFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D29GF-XXXHP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D29GFFP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
M38D29GCHP 8-BIT, FLASH, 6.25 MHz, MICROCONTROLLER, PQFP64
相關代理商/技術參數
參數描述
M38D24G4HP#U0 功能描述:IC 740/38D2 MCU QZ-ROM 64LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI,I²C,UART/USART 外圍設備:POR,PWM,WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC(J 形引線) 包裝:帶卷 (TR)
M38D24G4XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G4XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G5XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38D24G5XXXHP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER